ADEMCO VISTA-20SE User's Guide download pdf (Page 32)

Vista 20SEa Training Guide Page 32

6.5 4204 Relay Programming

Training Module

• Connect the Relay module across the console bus.

• Set 4204’s Dipswitch to device address 01 (switches 2 OFF and switches 3, 4, and 5 ON). Switch 1

determines the unit’s cover tamper response (ON= disabled, OFF=enabled).

• Program Address “* 25” with a 3 for a 4204 (4 Output relay module)

• Enter * 8 0 to move to “DEVICE PROGRAMMING”.

• The console will display “ENTER DEVICE No.”

• Enter the specific relay number 01, 02, 03, or 04 (The 4204 has 4 relays)

• Press * and the console will display a summary START screen.

• Press * and the console will display a summary STOP screen.

• Press * to move to “DEVICE ACTION” then enter 0 = not used, 1 = close for 2 secs, 2 = stay closed, or 3

= pulse on/off.

• Press * to move to “S TART EVENT” then enter 0 = not used, 1 = alarm, 2 = fault, 3 = trouble, or 4 =

restore.

• A Zone List must be used in conjunction with an event. If a zone type/system operation is to be used

instead of an event, enter 0.

• Press * to move to “START ZN LIST”. If a zone list is to be used to START the relay action, enter the

zone list number (1 to 3) (to be programmed in field *81) or 0 if a zone list is not being used.

• Press * to move to “START ZN TYP” then, if a zone type/system operation is being used, enter the

appropriate 2-digit code as listed below.

Choices for Zone Types Choices for System Operation

00 = No Response (Not used) 20 = Arming Stay 42 = **System Battery Low

01 = Entry/Exit # 1 21 = Arming Away 43 = Communication Failure

02 = Entry/Exit # 2 22 = Disarming (Code+Off) 52 = Kissoff

03 = Perimeter 31 = End of Exit Time 58 = Duress

04 = Interior Follower 32 = Start of Entry Time ** Use 0 (any) for Partition No. (P) entry

05 = Trouble Day/Alarm Night 33 = Any Burglary Alarm *** Or at Disarming, whichever occurs earlier)

06 = 24Hr Silent 36 = **At Bell Timeout ***

07 = 24Hr Audible 38 = Chime

08 = 24Hr Aux 39 = Fire Alarm

09 = Fire Alarm or Trouble 40 = Bypassing

10 = Interior w/Delay 41 = **AC Power Fail

24 = Silent Burglary

Press * to move to “START PARTITON” then enter the partition number 1 or 2 (or 0 for any)

Press * to move to “STOP ZN LIST”. If a zone list will be used to STOP, or restore, the device action enter

the zone list number, 1, 2 or 3 (to be programmed in *81 mode). If not used enter 0.

Press * to move to “STOP ZN TYP” then, if a zone type/system operation is being used, enter the

appropriate 2-digit code as listed above.

Press * to move to “STOP PARTITION” then enter the specific partition number 1 or 2 (0 for any)

Press * to move to the “START” summary and if correct, press * to move to the “STOP” summary and if

correct, press *.

Console will display “ENTER DEVICE No.” so that the next device may be programmed. If there are no

more, Enter 0 0 to quit.

If a zone list is to be used, enter *81.

Console will display “ZONE LIST No.”, then enter specific zone list 01, 02,or 03.

Press * to display “ENTER ZN NUM.”, enter the two digit zone number and press * to move to the next zone

to be included in this zone list.

After all zone lists have been entered press 0 0 to quit.

Press * to move to the next prompt, “DELETE ZN LIST”, enter 0 to save the list or 1 to delete and return to

the “ZONE LIST No.” prompt.

If all zone lists have been entered, press 0 0 to quit.

1 ... 31 32 33 34

Comments to this Manuals

No comments

ADEMCO VISTA-20SE User's Guide Page 32

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-20SE