ADEMCO LYNX Setup Guide download pdf (Page 17)

–17–

Data Field Descriptions

Defaults (where applicable) are Indicated in Text.

The following pages list all data fields in this Control (in numerical order). Use the blank programming form

to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.

Note: Entering a number other than the one specified will give unpredictable results.

✻

Installer Code

Enter 4 digits, 0-9

The Installer Code is used to enter the 4-digit Master Security Code. See

"Master Code" in the System Operation section for procedure.

✻21

Quick Arm Enable

0 = do not allow quick arm

1 = allow quick arm

If enabled, security code is not required to arm the system. The user

simply presses and holds down the AWAY or STAY key to arm.

✻22

Keypad Backlight Timeout

0 = no timeout; always backlight keys

1 = turn backlighting off after inactivity

This option allows the choice of either always backlighting the keypad or

turning the backlighting off after 10 seconds of keypad inactivity.

✻23

Forced Bypass

0 = no forced bypass

1 = provide automatic bypass of all open (faulted)

zones

All zones bypassed by this function will be displayed after the bypass is

initiated.

Note: UL installations: must be 0 (no forced bypass)

✻24

RF House ID Code

00 = disable all wireless keypad usage

01-31 = House ID

The House ID identifies receivers and wireless keypads.

If a 5827 Wireless Keypad or 5804BD/5804BDV Transmitter is to be

used, a House ID Code MUST be entered, and the keypad should be set

to the same ID.

✻25

Powerline Carrier Device (X-10) House ID

0 = A 4 = E 8 = I # + 12 = M

1 = B 5 = F 9 = J # + 13 = N

2 = C 6 = G # + 10 = K # + 14 = O

3 = D 7 = H # + 11 = L # + 15 = P

Powerline Carrier Devices require a House ID. This field identifies this

House ID to the Control. The Powerline Carrier Devices are

programmed in field ✻80.

✻26

Chime by Zone

0 = no (chimes on fault of any entry/exit or perimeter

zone when Chime mode is activated

1 = yes (chimes on fault of those zones assigned to

Zone List 3 when Chime mode on)

This option allows the installer to define the specific zones intended to

chime when faulted while the system is in Chime mode. If enabled, these

zones are defined in zone list 3 (see ✻81 Zone List Menu Mode).

✻27

Real Time Clock Display

0 = do not display the time

1 = display the time

Refer to the User’s Manual for setting the clock time and date.

✻29

Daylight Savings Time Start/End Month

0, 0 = no daylight saving time used

1-12 = start month and end month

Enter # + 10 for 10, # + 11 for 11, and # + 12 for 12.

✻30

Daylight Savings Time Start/End Week

0 = disable 4 = fourth weekend

1 = first weekend of month 5 = last weekend

2 = second weekend 6 = next to last

3 = third weekend 7 = 3

from last

Enter the appropriate start and end weekend of the month.

✻31

Single Alarm Sounding Per Zone

(per armed period)

0 = no limit on alarm sounding per zone

1 = limit alarm sounding to once per arming period for

a given zone

LYNXR/LYNXR24 - Applies to Long Range Radio Output if “0”

is selected in field ✻91

LYNXR-EN - Applies to Long Range Radio Output if Long Range

Radio is connected to the Trigger Single (Neg.) terminal #8.

UL installations: must be 0 (no limit)

This field applies only to burglary zones (zone response types 1-5, 10),

and affects long range radio reporting but does not affect central station

reporting.

Note: This field applies only to the bell and does not affect keypad

sounds.

✻32

Fire Sounder Timeout

0 = yes, fire sounder timeout after time programmed in

field

✻33

1 = no fire sounder timeout; continue sounding until

manually turned off

This Control complies with NFPA requirements for temporal pulse

sounding of fire notification appliances.

Temporal pulse sounding for a fire alarm consists of the following:

3 pulses – pause – 3 pulses – pause – 3 pulses. . .

✻33

Alarm Bell Timeout

0 = No timeout 2 = 8 min 4 = 16 min

1 = 4 min 3 = 12 min

This field determines whether the external sounder will shut off after

time allowed, or continue until manually turned off.

UL installations: must be set for a minimum of 4 min (option 1)

✻34

Exit Delay

00-99 = exit delay time in seconds

The system will wait the time entered before sounding an alarm if the

exit door is left open after the system has been armed.

UL installations: must be set for a maximum of 60 seconds

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 71 72

Comments to this Manuals

No comments

ADEMCO LYNX Setup Guide Page 17

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO LYNX