ADEMCO LYNXR-EN Setup Guide Page 1

Preliminary - 27 January 2003 LYNXR SeriesLYNXR SeriesLYNXR SeriesLYNXR Series Security Systems Programming Guide for LYNXR/LYNXR24 and LYN

- 10 - Field Function Programmed Values [ ] = Table 1 Default Value ✱95 RING DETECT COUNT FOR DOWNLOADING/REMOTE PHONE CONTROL MODE [15]

- 11 -*56 ENHANCED ZONE PROGRAMMING Use this mode to program zone information. Press *56 while in programming mode. Notes: (1) Entering a number

- 12 - F DELETE ZONE PARAMETERS 0 = Discard the delete request. 1 = Confirm the requested delete. If 00 is entered in the zone type, confirmation

- 13 -*80 DEVICE PROGRAMMING Use this mode to program Powerline Carrier Devices or zone lists for Chime by Zone feature. Press *80 while in programm

- 14 -*81 ZONE LISTS Use this mode to define zone lists for Powerline Carrier Devices and/or for the chime by zone feature. Press *81 while in progr

- 15 -*83 ENHANCED SEQUENTIAL MODE Use this mode to enter transmitter serial numbers. Press *83 while in programming mode. A 0 I ZONE NUMBER Ente

- 16 -*84 ASSIGN ZONE VOICE DESCRIPTORS Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when

-17-*85 RECORD CUSTOM VOICE DESCRIPTORS Use this mode to record up to 5 custom voice descriptors for use with zone announcements. Press *85 whil

- 18 -Zone No. Zone Alarm Report Input Loop Transmitter Vocabulary (A 01) Type (zt) Code in hex (rc) Type (I) No. (l) Serial Number Inde

- 19 -POWERLINE CARRIER DEVICES WORKSHEET FOR *80, and *81. Applicable only if Powerline Carrier Devices are to be used, or chime-by-zone feature is

- 2 -TABLE OF CONTENTS Data Fields...

- 20 -✱81 ZONE LISTS FOR OUTPUT DEVICES Fill in the required data on the worksheet below and follow the procedure in the installation manual a

- 21 -MONITRONICS LYNXR-EN PROGRAMMED VALUES The following table summarizes the values have been programmed into the Monitronics LYNXR-EN at the fa

- 22 -*80 OUTPUT DEVICES Start Stop Device Number Action Event Zone List Zone Type System Operation Restore of Zone List Zone type S

-23-INCOMINGPHONELINETO HANDSETPHONELINEWARNING:TO PREVENTRISK OFSHOCKDISCONNECTTELEPHONELINE AT TELECOMJACK BEFORESERVICINGTHIS UNIT.WEEKLY TES

MonitronicsINTERNATIONAL,INC.R 12801 Stemmons Freeway Suite 821 Dallas, Texas 75234 !"#$%#&a

- 3 - TO LOAD A DEFAULT SET: While in Program mode, press ✱97, then enter a number 1-4 corresponding to the default table desired. See the Installat

- 4 - Field Function Programmed Values [ ] = Table 1 Default Values ZONE SOUNDS AND TIMING (✱✱✱✱ 31– ✱ ✱ ✱ ✱ 39) ✱31 SINGLE ALARM SOUNDING/ZONE

- 5 -✱42 TWO WAY VOICE PHONE NUMBER Not Viewable. Press ✻ + Field Number to advance to next field. Field Function Programmed Values [ ] = Tabl

- 6 -Field Function Programmed Values [ ] = Table 1 Default Value NOTES: (1) If pager is enabled (Options 6-9 in Field *49) the end user canno

- 7 -Field Function Programmed Values [ ] = Table 1 Default Value TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✱59–✱76, & ✱89):

- 8 -Field Function Programmed Values[ ] = Table 1 Default Value ✱75 RF XMTR LO BAT RST RPT CODE | [1,0] ✱76 TEST RESTORE RPT CODE

- 9 -Field Function Programmed Values[ ] = Table 1 Default Value ✱91 LYNXR/LYNXR24 LONG RANGE RADIO/ALARM AUDIO VERIFICATION (AAV)/REMOTE PHONE