ADEMCO Symphony 8142 Installation Manual download pdf (Page 9)

– 9 –

10 INPUT S/N L

A022-4064 1

If the serial/loop number combination is not a duplicate in the system, a display showing the serial number

and loop number entry appears.

[∗] to continue

XMIT TO CONFIRM

PRESS ✱ TO SKIP

This prompt will only appear if you answered “Yes” at the first prompt in this section.

The system will enter a confirmation mode so that the operation of the actual programmed input can be

confirmed.

Activate the loop input or button that corresponds to this zone.

[∗] to continue

Entd A022-4063 1

Rcvd A022-4064 1

If the serial/loop number transmitted does not match the serial number entered, a display showing the

entered and the received serial/loop numbers appears.

If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e.,

summary display does not appear), press the [#] key twice and then enter (or transmit) the correct serial

number.

[∗] to continue

Zn ZT RC In: L

10 03 10 RF: 1s

If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and

a summary display will appear, showing that zone's programming. An “s” indicates that a

transmitter’s serial number has been enrolled.

[∗] to accept the zone information and continue

PROGRAM ALPHA?

0 = NO 1 = YES 0

If you want to program descriptors for zones now, enter 1 (Yes) and refer to the *82 Descriptor Programming

section for procedures. To program descriptors later, enter 0 (no).

[∗] to continue

ENTER ZN NUM.

(00 = QUIT) 11

If 0 (No) was entered at the Program Alpha prompt, the system will return you to the ENTER ZN NUM.

prompt for the next zone.

When all zones have been programmed, enter 00 to quit.

∗

∗∗

∗58 Expert Programming Mode Procedures (press ∗

∗∗

∗58 while in Data Programming mode)

SET TO CONFIRM?

0 = NO 1 = YES

0 = no

1 = yes (prompt appears after entering the serial and loop numbers to confirm each transmitter)

We recommend that you confirm the programming of every transmitter.

Zn ZT P RC HW: RT

01 09 1 10 EL 1

ZT P RC IN: L

10 – – – : –

A summary screen will appear, showing zone 1’s currently programmed values.

Enter the zone number being programmed, then press [∗]. In this example, zone 10 is being entered.

01-06, 09-24, and 49-64 = zone number

[D] = for assigning wireless key programming templates (see Wireless Key Programming Templates section

in i/i); lets you choose from a series of preset templates for easy programming of wireless key zones

00 = quit (when all zones have been programmed, press “00” to quit this menu mode)

[∗] to continue

Zn ZT P RC IN: L

10 00 1 10 RF 1

A summary screen with the selected zone’s current programming appears.

Begin programming zone information as follows:

Enter Zone Type (ZT; see Zone Type chart shown in *56 Menu Mode “Zone Type” prompt), Partition (P),

Report Code (RC) 0-9 only (use *56 mode for hex codes), and Input Device Type (IN)* sequentially (Loop

Number (L) is entered at the next prompt).

• Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the screen.

• Use the [C] key to copy the previous zone’s attributes.

* If HW (basic wired) or AW (Auxiliary) is entered for Input Device Type, the display will be similar to the

prompt shown, except that HW or AW will be under “IN”.

Press [∗] to save the programming and continue. If needed, press the [#] key to back up without saving.

For wireless devices (input types RF, UR, BR, RM), continue to the serial number/loop number prompt.

For wired devices, return to the initial summary screen prompt to begin programming the next zone.

10 INPUT S/N: L

AXXX-XXX –

Zn ZT P RC In L

10 03 1 10 RF: 1s

Manually enter the serial number (found on the transmitter label), by entering the digits in the “X” locations,

using the [A] (advance) or [B] (back) keys as required.

Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice,

but wait about 4 seconds before pressing the button the second time.

If you want to copy the previous zone’s serial number, press the [C] key.

Press [∗] to advance to the loop number, then enter loop number.

Press [∗] to accept the existing serial and loop number and continue to the “Confirm” prompt described in *56

Menu mode above.

If necessary, press [#] to back up and re-enter or edit the serial number.

If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a

summary display will appear, showing the programmed information for that zone.

Press [∗] to begin programming the next zone. See first “Summary Screen” prompt paragraph on previous

page.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Comments to this Manuals

No comments

ADEMCO Symphony 8142 Installation Manual Page 9

Comments to this Manuals