ADEMCO 4110XM Specifications download pdf (Page 19)

-19-

TO DETERMINE TOTAL STANDBY LOAD

ON BATTERY, ADD 100mA TO TOTAL OF

AUX. POWER OUTPUT AND REMOTE

KEYPAD CURRENTS.

1234567891011121314151617181920 21

EARTH GROUND

SEE INSTRUCTIONS

FOR PROPER GROUNDING

TELEPHONE WIRING

(VIA RJ31X* JACK DIRECT

CONNECT CORD)

*IN CANADA, CA38A JACK

No. 4127: 20mA

No. 4137AD: 60mA

No. 6127: 20mA

No. 6128: 30mA

No. 6137: 85mA

No. 5330: 105mA

BLACK: KEYPAD GROUND (–) RETURN

RED: KEYPAD PWR (+)

GREEN: DATA IN FROM KEYPAD

YELLOW: DATA OUT TO KEYPAD

REMOTE

KEYPAD

AUX. POWER

OUTPUT

10.5-13.8VDC

500mA MAX.

INTERRUPTS

FOR FIRE

ALARM RESET

NOTE:

KEYPAD

CURRENT MUST

BE INCLUDED IN

AUX. CURRENT

DRAIN

CALCULATIONS

}

GEL LEAD ACID TYPE.

BATTERY NORMALLY NEED NOT BE

REPLACED FOR AT LEAST 3 YRS.

BATTERY CAPACITY FOR EMERGENCY

STANDBY USE AT LEAST 4 HOURS.

BATTERY

12V, 4AH

OR 12V, 1.2AH

–

CONNECTOR TABS

USE UL LISTED

LIMITED ENERGY

CABLE FOR ALL

CONNECTIONS

FOR COMPLETE

INFORMATION, SEE

INSTRUCTIONS

N5478V4

PLUG-IN TRANS-

FORMER

16.5VAC, 25VA

(e.g. ADEMCO

No. 1321/TF2.

USE No. 1321CN

IN CANADA

TO 110VAC

UNSWITCHED

OUTLET (24HR)

–

CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE

ALARM HEADQUARTERS OR A CENTRAL STATION

SHALL BE PERMITTED ONLY WITH THE PERMISSION

OF THE LOCAL AUTHORITY HAVING JURISDICTION.

THE BURGLAR ALARM SIGNAL SHALL NOT BE CON-

NECTED TO A POLICE EMERGENCY NUMBER.

ALARM OUTPUT

10.5-13.8VDC, 2A MAX.

(600mA MAX FOR UL USAGE,

INCLUDING AUX. POWER)

STEADY FOR BURGLARY/PANIC,

PULSING FOR FIRE (e.g. USE ADEMCO

No. 702 OR 719 SIREN, OR 12V BELL)

FUSE

FOR REPLACEMENT,

USE SAME VALUE

BLK

RED

GRN

YEL

1000

OHMS

EOLR

1000

OHMS

EOLR

ZONE 5

ZONE 6

TIP

(BROWN)

RING

(GRAY)

TIP

(GREEN)

RING

(RED)

}

INCOMING

PHONE LINE

LOCATED AT

LOWER RIGHT OF

CIRCUIT BOARD

HANDSET

BLACK

RED

–

1000

OHMS

EOLR

1000

OHMS

EOLR

ZONE 1

ZONE 2

1000

OHMS

EOLR

1000

OHMS

EOLR

ZONE 3

ZONE 4

• MAXIMUM LOOP RESISTANCE (EACH ZONE) 300 OHMS (PLUS EOLR)

• RESPONSE, ZONES 1-6: 300-500MSEC

• ZONE 3 CAN BE PROGRAMMED FOR N.C. SENSOR FAST RESPONSE TO AN

OPEN: 10MSEC MAX

• ZONE 5 CAN BE PROGRAMMED FOR USE AS A FIRE ZONE. SEE DIAGRAM

No. 4116

ARMING/DISARMING

KEYSWITCH

(SINGLE LED, LOCKSWITCH,

TAMPER)

BATTERY

(e.g. No. 90-12)

CHARGING

VOLTAGE

13.8VDC

NOTE: MULTIPLE KEYPADS MAY BE

USED, BUT EACH 5330 KEYPAD

MUST BE ON AN INDIVIDUAL HOME

RUN. USE MAX. OF 220FT. OF #22

WIRE OR 550 FT. OF #18 WIRE.

WARNING:

TO PREVENT RISK OF SHOCK,

DISCONNECT TELEPHONE LINE

AT TELCO JACK BEFORE

SERVICING THIS UNIT.

THIS EQUIPMENT SHOULD BE INSTALLED IN

ACCORDANCE WITH THE NATIONAL FIRE PRO-

TECTION ASSOCIATION’S STANDARD 74 (NATION-

AL FIRE PROTECTION ASSOC., BATTERYMARCH

PARK, QUINCY, MA 02269). PRINTED INFORMA-

TION DESCRIBING PROPER INSTALLATION,

OPERATION, TESTING, MAINTENANCE, EVACUA-

TION PLANNING AND REPAIR SERVICE IS TO BE

PROVIDED WITH THIS EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) IT MAY NOT

CAUSE HARMFUL INTERFERENCE, (2) IT MUST ACCEPT ANY INTER-

FERENCE THAT MAY CAUSE UNDESIRED OPERATION.

COMPLIES WITH FCC RULES, PART 68

FCC REGISTRATION NO. AC398U-68192-AL-E

RINGER EQUIVALENCE: 0.7B.

WARNING:

OWNER’S INSTRUCTION NOTICE NOT TO BE

REMOVED. WEEKLY TESTING IS REQUIRED TO

ENSURE PROPER OPERATION OF THIS SYSTEM.

DOC LOAD NO.: 3

BLK

RED

GRN

YEL

No. 4281L or 4281M

RF RECEIVER

WIRELESS ZONES

4281L: UP TO 4

4281M: UP TO 8

{

OPTIONAL

SET RECEIVER’S DIP SWITCH

FOR DEVICE ADDRESS OF “0”

SEE RECEIVER’S INSTRUCTIONS

AUX PWR

OUTPUT

TERMS

•

EOL

POWER

SUPER-

VISION

RELAY

MODULE

A77-716B

•

4-WIRE SMOKE

OR COMBUSTION

DETECTOR

1000

OHMS

EOLR

HEAT

DETECTOR

ZONE 5

RED

BLK

–

VIOLET

IF PROGRAMMED FOR FIRE

1 2 ... 14 15 16 17 18 19 20

Comments to this Manuals

No comments

ADEMCO 4110XM Specifications Page 19

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO 4110XM