- 11 -
-
b
zz
-
b
SERIAL NUMBER
Enter the transmitter’s 7-digit serial number (printed on the transmitter). If an incorrect digit is entered,
press the [#] key to return to prompt (1A) .
When all 7 digits are entered, press the [*] key. If the serial and loop number combination is already
present in the system, or if less than 7 digits are entered, the keypad will emit a single long beep and
return to the (1A) prompt while displaying the “L”.
If the serial number is correct, press [*] again to save it and advance to the next prompt (1C) or, if the
zone type is 00, will return to the DELETE ZONE PARAMETERS CONFIRMATION PROMPT (F).
If the serial number is not correct, pressing [#], will delete the number and returns to the ENROLL MODE
prompt (1A). If 30 seconds pass and no entry has been made, the system returns to prompt (1A).
*
DELETE ZONE PARAMETERS CONFIRMATION
0 = Discard the delete request.
1 = Confirm requested delete.
*84 ASSIGN ZONE VOICE DESCRIPTORS
Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when the
system annouces any event involving a zone number. Press *84 while in programming mode.
NOTE:
Entry of a
number other than one specified will give unpredictable results.
ASSIGN ZONE VOICE DESCRIPTORS
0 = Exit mode, upon which this prompt blinks. Press [*] + any field number to go to that field.
1 = Enter mode
%
zz
ZONE NUMBER
Enter the 2-digit zone number (
zz
) for which this descriptor is being assigned.
[*] = Continue to next prompt (existing descriptors will be announced, then descriptor 1 will be repeated.)
00 = Exit Zone Voice Descriptor mode (
displays blinking 84; enter
* +
desired data field or menu mode number
)
b
vv
DESCRIPTOR 1
Enter [#] + 2-digit vocabulary index number of first descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 2 (descriptor 2 will be announced)
8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
'
vv
DESCRIPTOR 2
Enter [#] + 2-digit vocabulary index number of second descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 = accept word and advance to descriptor 3 (descriptor 3 will be announced)
8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
d
vv
DESCRIPTOR 3
Enter [#] + 2-digit vocabulary index number of third descriptor word for this zone.
To change the entered index number, press [#] + desired index number.
6 or 8 = accept word and advance to next zone (prompt A….zz) – zone descriptor will be announced
Press any other key to repeat the selected word
VOCABULARY INDEX
00 ½ sec pause
A
01 ALARM
02 ATTIC
B
03 BABY
04 BACK
05 BASEMENT
06 BATHROOM
07 BEDROOM
C
08 CHECK
D
09 DEN
10 DETECTOR
11 DINING
12 DOOR
E
13 EMERGENCY
F
14 FIRE
15 FLOOR
16 FRONT
G
17 GARAGE
18 GUN
H
19 HALL
I
20 INSIDE
J
K
21 KITCHEN
L
22 LAUNDRY
23 LIBRARY
24 LIVING
M
25 MAIN
26 MASTER
27 MESSAGE
28 MOTION
O
29 OFFICE
P
30 PATIO
31 POOL
R
32 ROOM
S
33 SHED
34 SHOP
35 SIDE
36 SLIDING
37 SMOKE
38 STORAGE
39 SYSTEM
U
40 UPSTAIRS
41 UTILITY
W
42 WINDOW
Y
43 YARD
Z
44 ZONES
45 1
ST
46 2
ND
47 3
RD
70 Custom Word #1
71 Custom Word #2
72 Custom Word #3
73 Custom Word #4
74 Custom Word #5
99 Blank
(to erase previously
programmed word)
SYSTEM WORDS
(Announced by system
– not programmable)
AC LOSS
ARMED
AWAY
BYPASSED
CHIME
DISARMED
DISARM SYSTEM
NOW
EXIT NOW
FAULT
INSTANT
LOW BATTERY
NOT
READY TO ARM
STAY
(34 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals