ADEMCO LYNX User's Guide download pdf (Page 4)

Step Action

(Cont.)

5) When the last zone has been entered, the display will remain on that zone. To exit this

mode and return to data field program mode, press 00 at the ZONE NUMBER prompt

6) Once all zones have been programmed, test each zone using the system’s Test mode.

Do not use the Transmitter ID Sniffer mode for this, since it will only check for

transmission of one zone on a particular transmitter, and not the zones assigned to each

additional loop.

c. Serial Number - This prompt can be used to enroll the transmitter serial number via RF

transmission or manually. If using RF Learning proceed to c. 1). If using the manual mode skip to

c. 2).

1) RF Learning - Two (2) transmissions (two key depressions at least five second apart) will be

required for BR type or four (4) transmissions (fault, restore and fault, restore) for UR or RF

type. BR type devices can be enrolled only by transmission from BR devices. Likewise, UR

and RF devices can only be enrolled by transmission from a UR or RF device.

If the learned serial number has a different loop number than that entered in *56 the system

will announce the Voice Descriptor, if it is programmed, followed by two beeps and will return

to Prompt (1A) and “L” will be displayed.

If the loop number captured by RF transmission and that entered in *56 mode match, the

system will announce the Voice Descriptor, if it is programmed, followed by three beeps and

return to Prompt (1A) and “LC” will be displayed. No additional transmissions are needed for

confirmation.

Note: BR type devices can be enrolled only by transmission from BR devices. Likewise, UR and RF devices can only

be enrolled by transmission from a UR or RF device.

2) Manual Entry - Enter the 7-digit serial number printed on the transmitter. If you enter an

incorrect digit, press the [#] key to backup to prompt (1A) and start over. When all seven

digits are entered press the [*] key.

3) Once all 7 digits have been entered, press the [*] key. If less than 7 digits are entered,

the keypad will emit a single long beep and return to the (1A) prompt without displaying

the “L”. If more than 7 digits have been entered, the first 6 digits will be saved along with

the last digit that was entered (entering 123456789 yields the serial number 1234569).

Note: If 52 seconds passes and no entry has been made, the system returns to prompt (1A).

F d. Delete Serial Number - This prompt can be used to delete the serial number programmed for the

zone.

1) Enter “0” to discard delete request or “1” to confirm

5. Exit Programming Mode as follows:

99 allows re-entry into the Program mode using Installer Code + 8 0 0.

98 inhibits re-entry into the Programming mode using the Installer Code.

6. Set RF House ID in the wireless keypads as follows:

a. 5804BD/BDV button key - Set the RF House ID per its instructions.

b. Powerline Carrier Devices - Set their House ID to “A,” (programmed as “0”) or use programming field *25 to

change the ID to avoid conflicts with existing installations.

7. Set the Real-Time Clock as follows:

a. Enter time/date setting mode by entering the User Code + FUNCTION + [63].

b. The hour prompt is displayed. Enter the correct hour, then press [*] to accept and advance.

c. For each subsequent prompt, enter the correct value, then press [*].

d. The system will exit this mode automatically after entering the year, or if no keys are pressed for 1 minute.

8. Test the system as follows:

a. After installation and programming, enter Installer Code + TEST.

b. To exit Test mode, enter Installer Code + OFF.

9. Assign desired User Codes by following the procedures on the next page and in the User Guide. Show the user

how to perform the various system functions.

Interactive mode programming

Interactive Mode Used to program

56 Enhanced Zone Programming

Zone characteristics, report codes and serial numbers

83 Enhanced Sequential Mode

5800 Series transmitter serial numbers

*84 Assign Zone Voice Descriptors Voice descriptors for each zone

Remote Programming (Downloading)

Perform site-initiated downloader session (to load central station ID) by Installer Code + [#] + [1].

- 4 -

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

ADEMCO LYNX User's Guide Page 4

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO LYNX