ADEMCO VISTA-250FBP Setup Guide download pdf (Page 11)

– 11 –

1*29 RF TX LOW BATTERY REPORTING [0]

1=enable; 0=disable

Must be 1 for UL installations.

1*30 RF RCVR CHECK-IN INTERVAL [02] |

02-15 times 2 hours; 00 disables supervision

Maximum is 2 (4 hr) for UL installations.

1*31 RF XMITTER CHECK-IN INTERVAL [02] |

02-15 times 2 hours; 00 disables transmitter supervision

Maximum is 2 (4 hr) for UL installations.

1*33 TOUCHTONE W/ROTARY BACKUP [0]

1=enable; 0=disable

1*34 COMM. SPLIT REPORTING [0]

0=no; 1=alarms and alarm restores primary, others

secondary; 2=open/close, test secondary, others primary;

3=fire alarms and fire restores to primary and secondary, all

others to secondary. See ✴51 for comments if using with

dual reporting.

NOTE: Split reporting should not be used with Dynamic

Signaling.

1*35

ACCESS CONTROL DIALER ENABLES - Not Used.

[0 0 0 0 0 0]

Trace

Trbl

Byp

Not Used

Syst

Alm

1=enable; 0=disable

Must Be Set To “0”.

1*42 CALL WAITING DEFEAT [0]

1=enable; 0=disable

1*43 PERM. KEYPAD BACKLIGHT [0]

1=enable; 0=disable, when disabled, display lights when any

key is pressed, and turns off after period of keypad inactivity.

1*44 WIRELESS KEYPAD TAMPER DETECTION – Not

Used. Must be set to “0”.

[0]

1=enable; 0=disable.

1*45 EXIT DELAY SOUNDING [1]

1=enable; 0=disable. Produces quick beeping during exit

delay if enabled.

NOTES:

Must be set to “0” in partition 1 for fire systems.

Must be enabled “1” for SIA installations.

See page 32, “SOUND OPTION”, prompt for disabling the

entry/exit beeps on individual keypads.

1*47 CHIME ON BELL 1 [0]

1=enable; 0=disable

1*48 WIRELESS KEYPAD ASSIGNMENT - Not Used. Must

be set to “0”.

[0]

0=disable; enter partition in which RF keypad used, 1-8.

1*49 SUPPRESS TX SUPERVISION SOUND [1]

1=disable; 0=enable.

Must be "0" for Commercial Burglary and Fire installs.

1*52 SEND CANCEL IF CODE + OFF [1]

1=no restriction; 0=within bell timeout period only.

Must be enabled “1” for SIA installations.

1*53 DOWNLOAD CALLBACK [0]

1=callback not required; 0=callback required.

Must be "0" for Commercial Burglary and Commercial Fire

installations.

1*55 EUROPEAN DATE FORMAT [0]

0=disable (mm/dd/yy); 1=enable (dd/mm/yy).

1*56 AC 50/60 Hz CLOCK SPEED [0]

1=50 Hz; 0=60 Hz.

1*57 5800 RF BUTTON GLOBAL ARM [0]

1=enable; 0=disable

Must be "0" for Commercial Burglary and Commercial Fire

installations.

1*58 5800 RF BUTTON FORCE ARM [0]

1=enable. If a zone is faulted after pressing button, console

will beep once. User should press button again within 4 sec.

to force bypass those zones. 0=disable.

Must be "0" for Commercial Burglary and Commercial Fire

installations.

1*60 ZONE 5 AUDIO ALARM VERIFICATION [0]

Enter 1 if 2-way audio (AAV) is being used; Enter 0 if it is not.

Must be "0" for Commercial Burglary and Commercial Fire

installations.

1*69 PRINTER TYPE - Not used. Must be set to “0”.

[0]

Enter 0 if you are using a parallel printer connected to the

VA8201 Alpha Pager Module.

Enter 1 if you are using a serial printer.

1*70 EVENT LOG TYPES

[1 0 0 0 1 0]

Alarm

Chk

Byp

O/C

Syst

Test

1=enable; 0=disable

1*71 12/24 HOUR TIME STAMP FORMAT [0]

0=12 hour; 1=24 hour

1*72 EVENT LOG PRINTER ON-LINE - Not Used. Must Be

Set To “0”.

[0]

0=disable; 1=enable

1*73 PRINTER BAUD RATE - Not Used. Must Be Set To

“0”..

[0]

1=300; 0=1200

1*74 RELAY TIMEOUT XXX MINUTES [000] | |

Enter relay timeout, 0-127 in multiples of 2 minutes, desired

for #80 Menu Mode time-driven event relay command

numbers "04/09" and #93 Menu Mode Output Programming

output command "56."

1*75 RELAY TIMEOUT YYY SECONDS [000] | |

Enter relay timeout, 0-127 seconds, desired for #80 Menu

Mode time driven event relay command numbers "05/10" and

#93 Menu Mode Output Programming command "57."

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 11

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP