ADEMCO VISTA-250FBP Setup Guide download pdf (Page 18)

– 18 –

PROMPT

EXPLANATION

Each zone must be assigned a zone type, which defines the way in which the system responds to faults in

that zone. Refer to the

Zone Type Definitions

section in the

VISTA-128FBP/VISTA-250FBP

Installation and

Setup Guide

for detailed definitions of each zone type. Enter the zone type desired (or change it, if

necessary). Available zone types are listed below.

00 = Assign for Unused Zones 14 = CO Detector Alarm

01 = Entry/Exit #1, Burglary 16 = Fire With Verification

02 = Entry/Exit #2, Burglary 17 = Waterflow

03 = Perimeter, Burglary 18 = Fire Supervisory

04 = Interior Follower, Burglary 19 = 24-Hour Trouble

05 = Trouble Day/Alarm Night 20 = Arm–STAY†

06 = 24 Hr. Silent Alarm 21 = Arm AWAY†

07 = 24 Hr. Audible Alarm 22 = Disarm†

08 = 24 Hr. Auxiliary 23 = No Alarm Response (e.g., relay activation)

09 = Fire Without Verification 27 = Access Point – Not Used

10 = Interior Delay, Burglary 28 = MLB Supervision (if VGM installed) – Not Used

12 = Panel Link Supervision – Not

Used

29 = Momentary Exit (used with VistaKey module) - Not Used

13 = Remote P/S

010 ZONE TYPE

PERIMETER 03

Zone number 010 and

Zone Type 03 entry shown

† These are special zone

types used with 5800

Series Wireless

Pushbutton Units that

result in arming the system

in the STAY or AWAY

mode, or disarming the

system, depending on the

selection made.

Press [✱] to continue.

010 Arm w/ Fault?

1 = YES 0 = NO 0

If you selected response type 1, 2, 4, or 10, this prompt appears. Enter 1 to enable arming of the partition

with this zone faulted. The zone must be restored (see Force Arming, the next prompt) before the exit delay

expires otherwise the system starts the entry delay and must be disarmed, or an alarm occurs.

010 Force Arming?

1 = YES 0 = NO 0

If you entered 1 (YES) at the previous prompt, this prompt appears. Enter 1 to enable the system to

automatically bypass the zone if it is faulted at the end of the exit delay.

If you enter 0 to disable and the zone is faulted at the end of exit delay, the system either performs the exit

error logic, if field 1✱20 is enabled, or an alarm occurs.

NOTE: Force Arming cannot be enabled for UL installations.

010 Vent zone ?

1 = YES 0 = NO 0

If you selected response type 3, this prompt appears. Enter 1 to enable the arming of the partition with this

zone faulted (force arm). The zone is automatically bypassed.

NOTE: The zone may be unbypassed simply by restoring the zone (e. g., closing the window), if the Vent

Re-arm option (next prompt) for the zone is enabled.

Enter 0 to disable.

Press [✱] to continue.

010 Vent Re-arm ?

1 = YES 0 = NO 1

If you entered 1 (YES) at the previous prompt, this prompt will appear. Enter 1 to enable the system to

automatically unbypass the zone when it is restored (e.g., by closing the window).

Enter 0 to disable. The zone is bypassed for the duration of the armed period regardless of the zone status.

Press [✱] to continue.

010 STAY MODE

None 0

If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter the STAY mode for this

zone (0-2).

0 = None. The zone is not bypassed when the partition is armed STAY.

1 = Stay 1. The zone is automatically bypassed when the user enters [User Code] + [3] (STAY) + [1].

2 = Stay 2. The zone is automatically bypassed when the user enters [User Code] + [3] (STAY) + [2].

NOTES:

0 (None) cannot be selected for response types 4 and 10.

Response types 4 and 10 are defaulted for STAY mode 1.

If the user enters [User Code] + [3] (STAY) + [3], all zones assigned to Stay mode 1 and 2 in the partition

are automatically bypassed.

If none of the zones in the partition are assigned to Stay mode 2, then when the user enters [User Code] +

[3] (STAY), all zones assigned to Stay mode 1 are automatically bypassed.

Press [✱] to continue.

010 Auto-stay ?

1 = YES 0 = NO 0

If you selected response type 1, 2, 3, 4, 5, or 10, this prompt will appear. Enter 1 to enable. The zone is

automatically bypassed if none of the entry/exit zones are opened during the exit delay time (no one exits the

premises). Enter 0 to disable.

NOTES: All zones enabled for auto-stay except types 3 and 5 have exit delay time when the partition is

armed. If auto-stay is enabled, make sure at least one zone is programmed for entry/exit in the same

partition, otherwise this zone will be automatically bypassed every time the partition is armed.

Press [✱] to continue.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 18

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP