ADEMCO VISTA-250FBP Setup Guide download pdf (Page 71)

— 71 —

V250FBP-SOC-V5

VISTA-128FBP / VISTA-250FBP

SUMMARY OF CONNECTIONS

TRANSFORMER

W/ENCLOSURE

ADEMCO No.1451

(supplied)

INPUT: 120VAC,

60HZ,

1.0A max. Connect to a

dedicated circuit.

See instructions for

proper earth ground

connections

12345678910 30

PROGRAMMABLE

AS KEYSWITCH LOOP

PROGRAMMABLE

AS TAMPER LOOP

2-WIRE GLASS BREAK

DETECTOR LOOP

2k (note 6)

Data in

Data out

BACK-UP LINE SEIZE

LED (GREEN)

Connect to main PCB

header J3 using ribbon

cable (supplied)

BACK-UP TLM ON HOOK

VOLTAGE THRESHOLD (BLUE)

INTACT: 25V

CUT: 13V

OPTIONAL 5140DLM BACK-UP DIALER MODULE

MAIN PCB SHIELD

BACK-UP PHONE JACK

SEE TELCO

JACK SHOCK

WARNING

BELOW

Make connections using 4142TR cable

VOLTAGE

TRIGGERS

(not supervised)

1 2 3 4 5 6 7 8 9

Make connections using

4142TR cable (supplied)

KEYPAD PORT #2

BELL 1

(WHITE)

BELL 2

(WHITE)

BLK + RED

OPTIONAL REMOVABLE

TERMINAL BLOCK KIT:

ADEMCO NO. 4142BLK

BELL

HORN

BELL

HORN

N.C.

N.O.

N.C.

N.O.

TO OTHER DEVICES

2k 2k 2k

ZONE 4

AC WIRING IS

SUPERVISED

BELL 1

BELL 2

ALARM POLARITY SHOWN

N.O.

POLE

N.C.

SPARE AUX

POWR #1

AUXILIARY POWER #1

1.0A MAX (STANDBY)

1.7A MAX (ALARM) (See Note 1.)

Max. Impedance: 0.6 Ohms

Special Application Circuit.

Fire & Burglary Devices on the ECP Bus

must be isolated using an ECP Isolator.

Refer to Instructions for specific examples.

ECP Bus: Max. Line Impedance: 50 Ohms

Special Application Circuit.

Connect to 12V, 12AH min/34.4AH max

lead acid batteries using cables supplied.

See instructions for required capacity.

Float charging voltage: 13.7VDC. Battery

normally need not be replaced for

at least 3 yrs.

J4 KEYPAD PORT #2

See instr. regarding port #2 use

1. GROUND (to keypad black wire)

4. DATA IN 2 (to keypad green wire)

5. AUX PWR #2 (to keypad red wire)

Rating: 10 - 14 VDC,

400mA max. See note 1

7. DATA OUT 2 (to keypad yellow wire)

(BLUE)

INTERFACE TO 5140DLM

MAIN DIALER ON HOOK

VOLTAGE THRESHOLD

INTACT:25V

CUT: 13V

BACK-UP DIALER EARTH

GROUND SCREW

(wire to main PCB

terminal #30)

J2 VOLTAGE TRIGGERS

See instructions for trigger use and programming

(default functions shown)

1. OUT 4 (SILENT PANIC/DURESS)

2. OUT 7 (TROUBLE)

3. OUT 3 (BURGLARY/AUDIBLE PANIC)

4. OUT 6 (SUPERVISORY)

5. OUT 2 (FIRE)

6. OUT 5 (REMOTE KEYPAD SOUNDER)

7. OUT 1 (OPEN/CLOSE)

8. GROUND

9. IN 1 (N.O. LOOP)

RATINGS: OUT 1, 5, 7:

LOW: 2K TO GROUND

HIGH: 10 - 14VDC, 20mA MAX

OTHER OUTS: LOW: 1K TO GROUND

HIGH: 10 - 14VDC THRU 5K

Attach 5140DLM module to main PCB shield using

4 standoffs (supplied)

1 2 3 4 5 6 7 8 9

BATTERY TABS

PINS 2, 3, 6, 8 & 9 NOT USED

RJ31X

MAIN

PHONE JACK

BELL OUTPUTS AUX. RELAY

INPUT

OUTPUT

CONNECTION OF THE FIRE ALARM

SIGNAL TO A FIRE ALARM HEAD-

QUARTERS OR A CENTRAL STATION

SHALL BE PERMITTED ONLY WITH

THE APPROVAL OF THE LOCAL

AUTHORITY HAVING JURISDICTION.

THE BURGLARY ALARM SIGNAL

SHALL NOT BE CONNECTED TO A

POLICE EMERGENCY NUMBER.

POLLING

LOOP

TO PREVENT

RISK OF

ELECTRICAL

SHOCK,

DISCONNECT

TELCO

JACK BEFORE

SERVICING

THIS PANEL

Connect

RJ31X using

cable supplied.

Supervision is

programmable

OUTPUT: 18VAC

72VA

BLACKWH

RJ31X

(connect using supplied cable)

Supervision is programmable

EARTH GROUND

• Ratings for zones 1,2:

- 2mA max for all smoke det.

(up to 16 detectors of the type

specified in the instructions can

be used)

- UL compatibility ID: A

TRNSFMR

TEST BURGLARY SYSTEM WEEKLY

The 5140DLM Dialer

Complies with FCC Rules, Part 68

FCC Reg. No.: AC398U-68628-MO-N

Ringer Equivalence: 0.7B

5193SD

SMOKE

4208SNF

28 29

4208U

The Main Dialer Complies with

FCC Rules, Part 68

FCC Reg. No.: AC3-USA-68192-AL-E

Ringer Equivalence: 0.7B

FOR DRY, INDOOR USE ONLY

The impedance at which a ground

fault is annunciated is 1,000 ohms

Special Application Circuit

Connect Only Fire Keypads to

AUX PWR # 2.

Each output is Class B and may be selected for Style Y

supervision or no supervision. (See main PCB jumpers

W1, W4 and #93 Menu Mode.)

FIRE CKTS: Use only devices listed as Special Application

NAC Devices in Installation and Setup Guide. Supervise

using 2k EOLR. Use polarized sounding devices and

backup batteries.

BURG CKTS: Supervision not req'd. EOLRs not req'd.

May use non polarized devices.

1.7A max.

See note 1, see instructions for compatible devices.

ALL CIRCUITS ARE POWER LIMITED EXCEPT THE OUTPUT

OF THE 1451 TRANSFORMER AND BACKUP BATTERIES.

ALL POWER-LIMITED WIRING MUST BE

SEPARATED FROM NON-POWER LIMITED

AND HIGH VOLTAGE WIRING BY 1/4 INCH

(6.4 mm)

For commercial fire, bell timeout must be a minimum of

6 minutes.

• All zones are Class B and provide Style B supervision

• Zone resistance (excluding EOLR):

- Zones 1, 2, 8: 100 ohms max

- Other zones: 300 ohms max

• Zone response: 350 - 500mS (all zones)

This equipment should be installed in accordance with the National Fire Protection Association's Standard 72

(National Fire Protection Assoc., Batterymarch Park, Quincy, MA. 02169). Printed information describing

proper installation, operation, testing, maintenance and repair service is to be provided with this equipment.

WARNING:

TYPES OF FIRE SIGNALLING SERVICE:

Manual fire alarm, automatic fire alarm, sprinkler supervisory and waterflow alarm, DACT, Radio Frequency (RF) and Multiplex.

UL Listed local control (non-coded). UL Listed central station and remote station protected premises unit when used with

5140DLM back-up dialer module. Installation limits under jurisdiction of local authority.

2-WIRE SMOKE

DETECTOR LOOP

N.C.

N.O.

SMOKE

2-WIRE SMOKE

DETECTOR LOOP

N.C.

N.O.

SMOKE

ZONE 1 ZONE 2

1511 12 13 14 16

KEYPAD PORT #1

REMOTE KEYPADS:

6160, 6160CR-2,

SEE NOTE 2

Red Blk Grn Yel

N.C.

N.O.

N.C.

N.O.

N.C.

N.O.

N.C.

N.O.

21 22

23 24

ZONE 3

2726

GLASS

BREAK

ZONE 7 ZONE 8ZONE 5 ZONE 6

FOR INSTRUCTIONS

SEE K0376V2,

DATED 7/09

AND QUICK REFERENCE

K0376QR DATED 7/09

WARNING:

• Do not mix fire and burg. sensors on one loop.

N.C. contacts for burg. usage only.

ZONE 1-8 NOTES

Polling Loop: Class B, Style 3.

Polling Loop Ratings:

(supervised) 128mA max. See note 1.

8-11 VDC

20 Ohms Max. Impedance

See instructions for compatible devices and

for max wire run length. Fire and Burglary

devices on the polling loop must be isolated

by use of a 4297 or VSI module.

Refer to instructions for specific examples.

- Maximum fire loop capacitance

is 100 uf.

Smoke DetectorControl Unit Delay, SecondsCircuit (zone)

Model Delay, Seconds

THE DELAY TIME MARKED ON THE INSTALLED DETECTOR(S) IS TO BE USED.

8 Seconds

Zone 2

Aux Relay

Zone 1

BELL CIRCUIT SUPERVISION JUMPERS

DO NOT CUT

NOTE: J2 Voltage triggers can only be used with the

4146 keyswitch for fire applications. Trigger Wiring must be

run in conduit within 20ft of the Control Panel.

(NOTE 5)

No more than one (1) wire per terminal may

be connected.

The combined standby current drawn from aux

pwr #1, aux pwr #2 and polling loop cannot

exceed 1.0A.The combined alarm current

drawn from aux pwr #1, aux pwr #2, polling

loop, bell 1 and bell 2 cannot exceed 2.3A.

NOTES

Use only 14-22 AWG wire.

See instructions on setting addresses & for

max # of keypads and wire run length

restrictions.

Maximum Loop Impedance is 1.17 ohms.

2k EOLR is Ademco Model EOL20.

This unit includes a Fire Alarm Verification feature that will result in a delay of

the System Alarm Signal from the indicated Fire Alarm circuits. The total delay

(Control Unit plus Smoke Detectors) shall not exceed 30 seconds. No other

Smoke Detector shall be connected to these circuits unless approved by the

local authority having jurisdiction.

COMMERCIAL FIRE AND BURGLAR ALARM PROTECTED PREMISES CONTROL UNIT

• Voltage rating, all zones - 12VDC.

AUX RELAY (FORM C)

programmable response

(not supervised)

Contact Rating:

28VAC/VDC, 2.8A

resistive loads

1 2 ... 66 67 68 69 70 71 72

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 71

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP