ADEMCO VISTA-250FBP Setup Guide download pdf (Page 8)

– 8 –

VISTA-128FBP/VISTA-250FBP Programming Form

Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,

see the

Partition-Specific Fields

section for programming these fields. Standard default (*97) values are shown in brackets [ ];

otherwise, default = 0.

*00 INSTALLER CODE | | |

Enter 4 digits, 0-9 [5140]

*04 ENABLE RANDOM TIMERS

Enter 1 to make available the randomizing of pre-programmed

time driven events for each partition. [0=disable].

Must be "0" for Commercial Burg installations.

*05 SYSTEM EVENTS NOTIFY [0]

1=yes, (messages sent via the RS232 port).

0=no, (no messages sent).

*06 QUICK EXIT [1]

1=enable; 0=disable

*08 TEMPORAL SIREN PULSE – Not Used at this time.

*09 ENTRY DELAY #1 [02] |

00, 02-15 times 15 seconds

Maximum "03" for Commercial Burglary installations.

The entry delay time and Burg Alarm Comm Delay (field *88)

combined cannot exceed 1 minute for SIA installations.

*10 EXIT DELAY #1 [04] |

00, 03-15 times 15 seconds

Maximum "04" for Commercial Burglary installations.

Minimum 45 seconds “03” for SIA installations.

*11 ENTRY DELAY #2 [02] |

00, 02-15 times 15 seconds (must be longer than Entry Delay

#1). Maximum "03" for Commercial Burglary installations.

The entry delay time and Burg Alarm Comm Delay (field *88)

combined cannot exceed 1 minute for SIA installations.

*12 EXIT DELAY #2 [08] |

00, 03-15 times 15 seconds (must be longer than Exit Delay

#1). Maximum "04" for Commercial Burglary installations.

Minimum 45 seconds “03” for SIA installations.

*13 BELL 1 TIMEOUT [03] |

01-15 times 2 minutes. Must be minimum 16 minutes for

Commercial Burglary installations. Must be minimum 6

minutes for Commercial Fire and SIA installations.

*14

TRIGGER OR RS232 INPUT [0]

Enter 1 to set J2 Pin 5 as a RS232 input to enable system to

receive serial data (75 baud).

Enter 0 to enable J2 Pin 5 as fire alarm trigger.

Must be set to “0”.

*15 KEYSWITCH ASSIGNMENT [0]

Enter partition in which keyswitch used, 1-8; 9=silences

Notification Appliance Circuit if fire present; 0=disable

*16 BELL 1 CONFIRMATION OF ARMING DING [0]

1=enable; 0=disable.

NOTE: If using a keyfob, when the button is pressed, either for

arming or disarming, the bell will ding indicating that the button

is working.

Must be "1" for Commercial Burglary installations.

*17 AC LOSS KEYPAD SOUNDING [1]

1=enable; 0=disable

Must be "1" for Commercial Fire installations.

*19 RANDOMIZE AC LOSS REPORT [2]

0= within 2 minutes; 1=10-40 min; 2=1-3 hours; 3=6-12 hours

without Type 13, 1-3 hours with Type 13.

*20 VIP MODULE PHONE CODE - Not used.

| |

Enter 01 - 09 for the first digit; enter [00], [11]

11 for “*” or 12 for “#” for the second digit.

Must be set to "00" for Commercial Burglary and Commercial

Fire installations.

*22 KEYPAD PANIC ENABLES [001]

1=enable; 0=disable 995 996 999

NOTE: Use for burglary panic types only. Do not use in

partition 1 in Fire systems.

*23 MULTIPLE ALARMS [1]

1=enable; 0=disable

Must be “1” for Commercial Burglary installations

*24 IGNORE EXPANSION ZONE TAMPER [0]

1=Ignore; 0=Enable tamper for RF and V-Plexs.

Must be "0" for Commercial Burglary and Commercial Fire

installations if using these devices.

*25 BURG.TRIGGER FOR RESPONSE TYPE 8 [1]

1=enable; 0=disable

*26 INTELLIGENT TEST REPORTING [0]

1=enable (no report sent if any other report was recently sent);

0=disable (send report at programmed interval, field *27)

Must be “0” for Commercial Burglary and Commercial Fire

installations.

*27 TEST REPORT INTERVAL [0024] | | |

Enter interval in hours, 0001-9999; 0000=no report;

Max. 0024 for Commercial Burglary and Commercial Fire

installations.

*28 POWER UP IN PREVIOUS STATE [1]

1=enable; 0=disable

Must be “1” for Commercial Burglary and Commercial Fire

installations.

*29 QUICK ARM [1]

1=enable; 0=disable

*30 MAIN DIALER TOUCHTONE OR ROTARY [1]

1=TouchTone; 0=rotary

*31 PABX ACCESS CODE | | | |

00-09; B-F (11-15)

*32 PRIM. SUBS. ACCT # | | | |

Enter 00-09; B-F (11-15) [15 15 15 15]

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 8

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP