ADEMCO VISTA-250FBP Setup Guide download pdf (Page 35)

– 35 –

Output Programming

The system supports up to 96 outputs. Outputs can be used to perform many different functions and actions. Each output

must be programmed to begin one of four types of ACTIONS at a designated START event, and end that ACTION at a

designated STOP event. The options used to start and stop these devices are described below, followed by the actual screen

prompts and available entries.

NOTE: If you are using outputs on the polling loop (e.g., 4101SN) no more than 20 of the polling loop outputs may be

programmed for the same START or STOP condition. Also, if you are using ZONE # for the START of a polling loop

output and want that output to stop when the same zone restores, the STOP programming MUST BE BLANK.

The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the

various summary displays of programmed data during programming.

ACTION (A) The "ACTION" of the device is how the device will respond when it is activated by the "START"

programming. You may want the device to activate momentarily, to pulse on and off continuously, or to

remain activated until some other event occurs to stop it. There are five different action choices:

• ACTIVATE for 2 SECONDS and then reset. If selected, it is not necessary to program a stop

parameter.

• ACTIVATE and REMAIN ACTIVATED until stopped by some other event.

• PULSE ON and OFF until stopped by some other event.

• NO RESPONSE when the device is not used.

• TOGGLE on and off alternately with each activation of event. Do not program a stop parameter as

this may cause unpredictable results.

START (STT) The "START" programming determines when and under what conditions the device is activated. The

following START options are available:

1) EVENT (EV) is the condition (alarm, fault, trouble) that must occur to a zone or group of zones (zone

list) in order to activate the device. These conditions apply

only

when a zone list is used. The different

choices for "EVENT" are listed below and in “Programming Relays” later in this section.

• ALARM Action begins upon any alarm in an assigned zone in the zone list.

• FAULT Action begins upon any opening of an assigned zone in the zone list.

• TROUBLE Action begins upon any trouble condition in an assigned zone in the zone list.

• NOT USED Action is not dependent upon one of the above events.

ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular

device. Note that there are a total of 15 zone lists that can be programmed; when the selected EVENT

(alarm, fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (01-15), activation of the

selected device will START.

2) ZONE # A specific zone going into alarm, fault, trouble, or restore (Event programming) can be used to

start the relay action. Enter the 3-digit zone number (000-250).

3) ZONE TYPE/SYSTEM OPERATION (ZT). If all zones to be used to start the device have the same

response type, and there are no other zones of this type that are not to activate this device, then

“ZONE TYPE” may be used instead of a "ZONE LIST" and "EVENT” to activate the device.

If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the device, enter

the appropriate choice under the “ZONE TYPE” option.

The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “EVENT/ZONE

LIST” combination.

If a specific "ZONE TYPE" is chosen, any zone of that response type going into alarm, trouble, or fault

will cause the device to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for

the STOP programming, any zone of that type that

restores

will de-activate the device.

If a "SYSTEM OPERATION" is chosen, that operation will cause the device to activate as selected in

"ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in

“Programming Relays” later in this section, and on the Programming Form.

4) PARTITION NO. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an

occurrence on one partition (1-8), or any partition (0).

STOP (STP):

The "STOP" programming determines when and under what conditions the device is de-activated. The

following options are available:

1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates

when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs

regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is

normally only used when a "ZONE LIST" is used to start the device.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 35

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP