ADEMCO VISTA 10 Setup Guide download pdf (Page 27)

Section 4 - Data Field Programming

4-3

FIELD TITLE and DATA ENTRIES EXPLANATION

✱

Secondary Phone No.

Enter up to 12 digits. Do not fill unused

spaces.

0–9, # + 11 for

‘

✱

’

, # + 12 for ‘#’, # + 13 for a

pause (2 seconds)

If you enter fewer than 12 digits, exit by pressing [

✱

] and

next field number (e.g., 43). To clear entries from field,

press

✱

. See NOTE if field

✱

41 also.

NOTE:

If you wish to send a report to a pager, see field

✱

on a following page.

✱

Subscriber Account No.

Enter digits 0–9; # + 11 for B; # + 12 for C;

# + 13 for D; # + 14 for E; or # + 15 for F.

Enter

✱

the fourth digit if a 3-digit account no. (for 3+1

dialer reporting format) is used.

Enter 0 as the first digit of a 4-digit account number for

numbers 0000–0999.

This field is also used as the Long-Range Radio Subscriber

Account No.

Exit field by pressing

✱

and next desired field number.

✱

Phone System Select

If Central Station Receiver

not

on WATS

line: 0 = Pulse Dial; 1 = Tone Dial

If Central Station Receiver

on WATS line: 2

= Pulse Dial; 3 = Tone Dial

Selects the type of telephone service.

✱

Report Format

0 = 3+1; 4+1 ADEMCO Lo Speed Standard

(this is the default)

1 = 3+1; 4+1 Radionics Standard

2 = 4+2 ADEMCO Lo Speed Standard

3 = 4+2 Radionics Standard

6 = 4+2 ADEMCO Express

7 = ADEMCO Contact ID

Reporting

8 = 3+1; 4+1 ADEMCO Lo Speed Expanded

9 = 3+1; 4+1 Radionics Expanded

Selects the format to be used to report to the central station.

Enter 1 digit (0–9).

(Enter

✱

as the 4th digit of

✱

43 if 3+1 dialer reporting is to

be used.)

See field

✱

27, which may override this field’s selection.

NOTE:

The maximum number of alarm and alarm restore

reports during one armed period is determined by field

✱

92.

✱

Split/Dual Reporting

0 = disable (Backup report only)

1 – 5 (refer to table at right for reporting to

the Primary and Secondary telephone

Numbers.

6 – 9 (refer to table at right for reporting to a

pager and Primary telephone no.).

You must enter the pager number as

the secondary phone number in field

✱

42 for this function to operate

To Primary No. To Secondary No.

1 = Alarms, restore, cancel Other reports

2 = All except open/close, test Open/close, test

3 = Alarms, restore, cancel All reports

4 = All except open/close, test All reports

5 = All reports All reports

To Primary No. To Paging No.

(Secondary)

6 = All reports except Open/Close Alarms/open/close, troubles

7 = All reports Alarms, troubles

8 = All reports Alarms/open/close, troubles

9 = All reports except Open/Close Alarms, open/close for users

5 - 25

, troubles

A 10-digit code is sent to the pager that is coded in the following format:

4-digit Subscriber No. SSSS

–EEE–NNN 3-digit

User or Zone No. (as entered in field

✱

43)

3-Digit Event Code (EEE), as follows:

911 = Alarm (NNN = Zone No.)

001 = Open, System disarmed (NNN = User No.)

002 = Close, System armed (

NNN = User No.)

811 = Trouble (

NNN = Zone No.)

NOTE:

The first digit of the Subscriber No. entered in field

✱

43 must be 1–9 (do not use 0); the last 3 digits

can be 0–9.

Failure to observe this requirement may interfere with paging services.

Example 1.

Pager displays: 1234–911–004

This indicates that Subscriber No. 1234’s system is reporting an Alarm (911), due to zone 4 being faulted

(004).

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 79 80

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 27

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10