ADEMCO VISTA 10 Setup Guide download pdf (Page 59)

10-1

SECTION 10

System Operation

•••••••••••••••••••••••••••••••••••••••••••••••••

Security Codes

The system supports up to seven security codes; Installer, Master, four secondary user, and Duress, described as follows:

Code Description of Code Function and Programming

Installer (User 1)

The factory default Installer Code is "

4-1-1-1

", but may be changed in field

✱

20. The Installer code

cannot be used to disarm the security system if it was not used to arm the system. The Installer code

must be used to program the 4-digit Master Code.

Master (User 2)

The Master security code permits access to the system for arming, disarming, etc. Opening and closing

reports are sent for the Master Code as No. 02, with the appropriate subscriber number.

•

assign

a Master Code, enter

Installer Code + 8 + 2 + 4-digit Master Code

•

change

the Master Code, enter

Master Code + 8 + 2 + New Master Code + New Master Code

Only the Master code can be used to assign, change, or delete the secondary 4-digit user codes.

Secondary Users 3-6

Secondary User codes permit access to the system for arming, disarming, etc.

•

assign (

change)

a Secondary security code, enter

Master Code + [CODE] key + User No.

(3–6) + desired 4-digit Secondary Code.

delete

a Secondary security code, enter

Master Code + [CODE] key + User No. (3–6).

Secondary user codes are sent as Nos. 3 through 6 respectively, with the appropriate subscriber number.

Duress (User 8)

Intended for use when

forced

to arm or disarm the system under threat. When used, the system will act

normally, but can

silently

notify the central station,

if that service has been provided

•

program

a Duress code, enter

Master code + [8] key + [8] key + new 4-digit Duress Code.

•

change

a Duress code, enter

Master code + [8] key + [8] key + desired 4-digit Duress Code.

•

delete

a Duress code, enter

Master code + [8] key + [8] key

and stop.

The Duress Code must differ from the Master Code or any other User’s Code.

Keypad Functions

The following is a brief list of system commands. For detailed information concerning system functions, refer to the User's Manual.

Function or Keypad Display Description

Silence Alarms

Pressing any key silences the keypad sounder for 10 seconds. Disarming the system silences

both keypad and external sounders.

Disarmed, Not Ready

Before arming, the system must be in the READY condition (all zones must be intact). If the

NOT READY

message appears, press the READY [

✱

] key to display faulted zones.

Arming AWAY

Enter 4-digit security code + AWAY [2] key.

Arming STAY

Enter 4-digit security code + STAY [3] key.

Arming INSTANT

Enter 4-digit security code + INSTANT [7] key.

Arming MAXIMUM

Enter 4-digit security code + MAXIMUM [4] key.

Quick Arming

(if enabled)

Simply press [#] key in place of code, then press AWAY, STAY, INSTANT, or MAXIMUM to

arm system as desired. Note that the [#] key cannot be used in place of the 4-digit security code

when disarming the system.

Disarming

Enter 4-digit security code + OFF [1] key.

Bypassing Zones

Enter 4-digit security code + BYPASS [6] key + zone number(s).

Forced (Quick) Bypass (

if enabled)

To automatically bypass all faulted zones, use the "Quick Bypass" method: Enter 4-digit

security code + BYPASS, then wait for all open zones to be displayed. Arm when display

indicates

Bypass

and

Ready to Arm

Chime Mode

Enter 4-digit security code + CHIME [9] key. To turn chime off, enter code + CHIME again.

SUMMARY OF ARMING MODES

Features for Each Arming Mode

Arming Mode

Exit

Delay

Entry

Delay

Perimeter

Armed

Interior

Armed

AWAY Yes Yes Yes Yes

STAY Yes Yes Yes No

INSTANT Yes No Yes No

MAXIMUM Yes No Yes Yes

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 79 80

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 59

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10