ADEMCO Vista-128FB Setup Guide download pdf (Page 47)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-24

Paging Service Advisory

If you are setting up the software for the first time,

contact your paging service provider for the following

two pieces of information:

• The exact access number to be used with each

receiving device

• The correct PIN number for each receiving device.

Pager Formats

The system supports pager formats numeric and

alphanumeric.

Numeric Format

SSSS P EEE ZZ, where:

SSSS The partition’s 4-digit subscriber number

(field ✳32)

P Partition number

EEE 3-digit event code

ZZZ 3-digit zone or user number

NOTE: If any of the digits for the subscriber number

are hex digits (A, B, C, D, E, F), they will be replaced

with 0, 1, 2, 3, 4, 5, respectively, on the pager display.

Numeric Format Event Codes

Event Code

Alarm 333

Trouble 555

Open 444

Close 777

Other 000

Alphanumeric

PP Date Time EA ZZZ SSSS AD

Where:

PP Partition number (e.g., P1)

Date Date the event occurred (e.g., 03/15/00)

Time Time the event occurred (e.g., 01:16AM)

EA Event alpha descriptor (see APPENDIX

ZZZ Zone or user number

SSSS The partition’s 4-digit subscriber number

(in field ✳32)

AD The zone’s programmed alpha descriptor

✳

✳ If the event is an arming or disarming, a 6-

character descriptor can be sent for the user,

if programmed, instead of the user number.

The descriptor can be programmed only via

the Compass Downloader.

The installer code has a default of INSTLR

and user number 002 has a default of

MASTER for the 6-character descriptor.

Mounting the Alpha Pager Module

The Alpha Pager Module (APM) may be mounted in

the control cabinet if space is available or, if this is not

possible, on the side of the cabinet or adjacent to it.

Do not mount the Alpha Pager Module on the

cabinet door or attempt to attach it to the PC

board.

To mount the Alpha Pager Module, perform the

following steps:

Step Action

1 If you are mounting the Alpha Pager

Module inside the control cabinet, attach it

to the cabinet’s interior surface with 2-faced

adhesive tape.

2 If you are mounting the Alpha Pager

Module outside the cabinet, use the bracket

interface (Ademco Part Number K5350).

Wiring the Alpha Pager Module

The Alpha Pager Module connects via the 4142TR

cable to the J8 connector on the VISTA-128BP/VISTA-

250BP.

To wire the Alpha Pager Module, refer to Figure 3-30

and perform the following steps:

Step Action

1 Connect the 4142TR to J8 on the control.

2 Connect the Brown wire of 4142TR to the

Orange wire of the APM.

3 Connect the Green wire of the APM to TB1-

23 of the control panel.

4 Connect the Red and Black wires of the APM

to terminals 6 and 7 (auxiliary power (+) and

(-), respectively) of the control.

5 Connect the APM RJ11 connector labeled

LINE to the handset terminals on the control

panel (terminals 26 and 27).

6 Connect the handset side of telephone line to

APM RJ11 connector labeled PHONE

(Optional) (Brown and Gray wires of Phone

Cord).

7 If you are using a parallel or serial printer,

connect the printer according to the

instructions accompanying the APM.

• The serial printer must be configured for a

baud rate of 1200, eight data bits, no parity,

and one stop bit. (8/N/1).

• The serial printer and Home Automation

cannot be used on the same system. If you

want to use a printer and Home Automation,

you must use a parallel printer.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 146 147

Comments to this Manuals

No comments

ADEMCO Vista-128FB Setup Guide Page 47

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO Vista-128FB