ADEMCO Vista-128FB Setup Guide download pdf (Page 72)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

4-10

function the same as alpha keypads, except when the

code + # 73 is entered. This entry will allow

momentary access to ALL access points in the

partition to which the keypad is assigned. To program

the wireless keypad, enter the partition the keypad is

assigned to in field 1*48.

Using an RF Transmitter Zone

A button type RF transmitter (5804) can be used to

provide access or egress for up to 4 doors. One button

will control one door. Also, a button can be used to

provide access or egress due to a panic or duress

condition.

An RF transmitter (5816) can be used with a remote

switch to provide exit in case of a fire alarm using a

PassPoint event action. To program the RF

transmitter for access control, perform the following

steps:

Step Action

1 Enter Zone Programming in the #93 Menu

Mode.

2 Program the zone with a response type 27

(Access Point).

3 Enter the access point number (00-31) of the

door.

4 Indicate whether RF device is for entry or

exit.

5 Enter the partition number

6 Enter the input type: button RF (03).

7 Enter the loop number.

8 Enroll the serial number

See Zone Programming in the Programming Guide for

a detailed explanation.

• RF buttons and pendants must be assigned

to a user number in order to function. See

SECTION 9: User Access Codes

for the

procedure.

• An RF transmitter will not provide access or

grant if the system is in any test mode.

Control of Lighting and Appliances

Lighting and appliances can be controlled when an

access or exit event occurs. Lights or appliances can

be automatically turned on or off when a valid entry or

egress request is presented at an access point. To

control these devices, the VISTA-128BP/VISTA-250BP

relays or the ACS relays or triggers are used with

keypads and/or RF transmitters whose response type

is Access Point (27). To program the control of lighting

and appliances, perform the following steps:

Step Action

1 Enter Output Programming in the #93 Menu

Mode.

2 Program all the information for the relay.

3 Select the output type: ECP (1) (4204) or (2)

(X-10).

See Output Programming in the Programming Guide

for a detailed explanation.

Using the VISTA-128BP/VISTA-250BP for Stand-

Alone Access Control

The VISTA-128BP/VISTA-250BP can be used for

access control without interfacing to PassPoint ACS or

VistaKey. A user can trigger an access point (i.e., door

strike) for 2 seconds by entering User Code + [0]. To

program the VISTA-128BP/VISTA-250BP for Stand-

Alone access control, perform the following steps:

Step Action

1 Enter Output Programming in the #93 Menu

Mode.

2 Program the output type as 1, or 2.

3 For type 1, program the ECP address and

relay number.

4 For type 2, program the house and unit codes.

Program the relay number in field 1∗76

(partition-specific).

See Output Programming in the Programming Guide

for a detailed explanation.

Programming for ECP Long Range Radio

• Program the LRR in Device Programming in the

#93 Menu Mode Programming.

• Field ✳56: Selects the time the panel should wait

before it attempts to send a message to the second

destination.

• Field ✳57: Select the initial reporting destination

for messages.

• Field ✳58: Select events for the primary sub’s ID

• Field ✳59: Select events for the secondary sub’s

ID.

Programming for TeleSmart

The TeleSmart module has a fixed address of 24 (it

cannot be changed). Set Device Address 24 for Device

Type 11 in the control’s Device Programming mode.

Also, Device Address 23 must be set for Device Type

01, Alpha Console, but do not actually connect a

device to the control panel set to that address.

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 146 147

Comments to this Manuals

No comments

ADEMCO Vista-128FB Setup Guide Page 72

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO Vista-128FB