ADEMCO Vista-128FB Setup Guide Page 50
- Page / 147
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
VISTA-128BP/VISTA-250BP Installation and Setup Guide
3-26
Step Action
4 Connect the leads to TB1 in the following
order:
a. All ground leads to terminals 2, 5, and 9.
b. The DSM, (optional) RTE, and General
Purpose leads to terminals 6, 7, and 8,
respectively.
c. Door strike (or mag lock) lead to terminal
10.
d. Local +12V or +24V supply lead to
terminal 1.
e. Local +12V or +24V supply lead to the N/C
relay terminal 11 (if a mag lock is being
used), OR to the N/O relay terminal 10 (if
a door strike is being used).
5 Connect the (–) polling loop and (+) polling
loop leads (from the VISTA-128BP/VISTA-
250BP) to terminals 4 and 3, respectively.
6 Set the Address Select switch to the desired
access door number (1-15).
7 Repeat steps 1 through 6 for each VistaKey
being installed.
Connecting the Card Reader
Lead from Reader Lead Color To VistaKey TB3
Terminal #
Green LED Orange 1
Ground* Black 2
DATA 1 (Clock) White 3
DATA 0 (Data) Green 4
+5VDC† Red† 6
+12VDC† Red† 7
* TB-3 Terminal 5 is also a ground and may be used
instead of terminal 2. Terminals 2 and 5 are a common
ground.
† Connect to +5VDC OR +12VDC per reader
manufacturer’s specification.
+
WEEKLY TESTING IS REQUIRED
TO ENSURE PROPER OPERATION
OF THIS SYSTEM.
POLE Door Strike/Mag Coil
DATA 1 (WHITE)
DATA 0 (GREEN)
NOTE 1: USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS.
NOTE 2: VISTAKEY TB3 TERMINAL 5 IS A GROUND AND MAY BE
USED INSTEAD OF TB3 TERMINAL 2. TB3 TERMINALS 2 AND 5 ARE
A COMMON GROUND.
NOTE 3: WHEN USING TRIGGER TO TURN ON AN LED OR BUZZER,
RETURN HIGH SIDE OF LED OR BUZZER TO TB3 TERMINAL 7.
TRIGGER RATING IS 15mA AT 12VDC.
+5V
GND
TRIGGER (SEE NOTE 3)
+12V (RED)
ZONE C (General)
ZONE A (DSM)
ZONE B (RTE)
POLLING LOOP -
14V MAX (12V @ 85-160mA Nominal)
POLLING LOOP +
GND
GND
GND
N/O DOOR STRIKE POWER
N/C MAG COIL POWER
2
3
4
5
6
7
8
11 1223456789101
RELAY CONTACT RATINGS:
3A @ 28VDC MAX. (RESISTIVE LOAD)
TB 1
TB 3
1
READER INTERFACE CABLE
GND (BLACK)
RDR LED (ORANGE)
TO ALARM SYSTEM
CONTROL PANEL
POLLING LOOP TERMINALS.
NO
CONNECTION
VISTAKEY
THIS DEVICE COMPLIES WITH PART 15 CLASS A
LIMITS OF FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1) IT MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) IT MUST ACCEPT ANY INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
K1
DOOR
CONTROL
RELAY
FOR ADDITIONAL RATINGS AND
SPECIFICATIONS, REFER TO
INSTALLATION INSTRUCTION
FOR THE VISTAKEY-SK.
THIS EQUIPMENT SHOULD BE INSTALLED IN
ACCORDANCE WITH THE NATIONAL FIRE
PROTECTION ASSOCIATION'S STANDARDS 70 &
74 (NATIONAL FIRE PROTECTION ASSOC.,
BATTERYMARCH PARK, QUINCY, MA. 02269).
PRINTED INFORMATION DESCRIBING PROPER
MAINTENANCE, EVACUATION PLANNING AND
REPAIR SERVICE IS TO BE PROVIDED WITH
THIS EQUIPMENT.
TO TB1, 11 OR 12
+ 12 VDC TO ONLY
ONE OF THESE INPUTS.
(FROM TB1-1)
Figure 3-31: Wiring the VistaKey
Access Control Using the PassPoint Access Control System
The VISTA-128BP/VISTA-250BP interfaces with the
PassPoint ACS via the VISTA Gateway Module
(VGM). The VGM is connected between the ECP bus
(keypad terminals) of the control and the network bus
of the PassPoint ACS.
The control sends the VGM its status information,
event log entries, and entry/exit requests (inputs
programmed with response type Access Point) from
keypads, hardwired zones, and RF transmitters.
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Related products and manuals for Security access control systems ADEMCO Vista-128FB
(5 pages)
(76 pages)
(24 pages)© 2020, manymanuals.com. All rights reserved. | 0.461 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals