ADEMCO VISTA-128B Setup Guide download pdf (Page 251)

¬.l

K3271 7/98

N.C.

N.O.

2k EOLR

(note 1)

2k EOLR

(note 1)

BELL

SIREN

NO CONNECTION

TRANSFORMER

16.5VAC, 40VA

ADEMCO No.1361

(IN CANADA

USE No. 1361CN)

or 4300 IF

X-10 DEVICES

WILL BE USED

Connect to

24hr. 120VAC,

60 Hz Outlet

Red Blk Grn Yel

REMOTE KEYPAD

Use 4137AD/6137/6128

5137AD/6139

(Addressable keypads) only

N.C.

2k EOLR

(note 1)

2k EOLR

(note 1)

N.C.

2k EOLR

(note 1,4)

TIP

(BROWN)

RING

(GRAY)

TIP

(GREEN)

RING

(RED)

Handset

Incoming

Phone Line

Telephone connections

using Ademco No. 620

RJ31X direct connect

cord.

EARTH GROUND

Connect to good earth

ground to maintain im-

munity to transients.

See Instructions for

proper grounding.

SMOKE

4190

RPM

4278

PIR

Polling loop rating: 128mA max. See

Installation Instructions for maximum

number of devices supported and

maximum wire run length

VISTA-128B

SUMMARY OF CONNECTIONS

USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS

Zone resistance (Excluding EOLR):

ZONE 1,8: 100 OHMS MAXIMUM

ALL OTHER ZONES: 300 OHMS MAXIMUM

ZONE 1

ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 ZONE 9

2-WIRE SMOKE

DETECTOR LOOP

(Also supports NO/NC Burg contacts)

POLLING LOOP

Programmable Response

(Fast/Normal) Loop

LATCHING TYPE GLASS

BREAK DETECTOR LOOP

Data in

Data out

12345678910 11121314151617181920 212223242526

28 29 30

RED (+)BLK (-)

Connect to

12VDC, 4AH

or 12VDC, 7AH

GEL CELL

BATTERY

CHARGING

VOLTAGE

13.7VDC

See

Installation

Instructions for

required

capacity

Replace

every

3 years

NOTE:

WHEN POWERING UP

THE PANEL, PLUG THE

TRANSFORMER IN BEFORE

CONNECTING THE BATTERY.

See Installation Instructions

for max # of keypads

and for max wire run length.

ALARM SOUNDER OUTPUT 10VDC - 13.8VDC

AUXILARY POWER OUTPUT

9.6VDC - 13.8VDC,

750mA maximum

Note: Include current drawn

by keypads and polling loop

devices when making

auxiliary power calculations.

NOTES:

1. Zone 1 may be selected for EOLR supervised

or normally closed (no EOLR) operation via

cut jumper. (Cut red jumper for normally closed

operation. Do not cut for Fire Usage). Zones 2-8

may be selected for either operation via program

field *41.

Zone 1 supports 2-wire smoke detectors.

See Installation Instructions for recommended type

and maximum number of detectors supported.

Zone 7 may be used for remote keyswitch arming/disarming.

See Installation Instructions for wiring instructions.

Zone 8 supports 2-wire latching type glass break detectors.

See Installation Instructions for recommended type and

maximum number of detectors supported.

1 2 3 4 5 6 7 8 9

1. Not Used

2. Ground-

3. Out 1 (Ground Start)

4. Ground-

5. Out 2 (fire)

6. Ground-

7. Out 3 (burg/aud. panic)

8. Ground

9. Out 4 (silent panic/

duress)

Optional programming:

Out 1: Open/close or keypad-like sounding

Out 2: Armed LED

Out 4: Ready LED

Ratings for Out 1:

Active: 10VDC-13.8VDC through 4k OHMS

Not Active: 100 OHMS to ground

Ratings for out 2-4:

Active: 10VDC-13.8VDC through 5k OHMS

Not Active: 1k OHMS to ground

N.C.

N.O.

N.O. N.O.

2k EOLR

(note 1,2)

N.O. N.O.

N.O.

N.C.

N.O.

2k EOLR

(note 1)

2k EOLR

(note 1,3)

N.C.

GLASS

BREAK

1 2 3 4 5 6 7 8 9

MAKE CONNECTIONS USING

No. 4142TR CABLE

WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED

Fire

Usage

Burg.

Usage

CONNECTION OF THE FIRE ALARM SIGNAL

TO A FIRE ALARM HEADQUARTERS OR A

CENTRAL STATION SHALL BE PERMITED

ONLY WITH THE APPROVAL OF THE LOCAL

AUTHORITY HAVING JURISDICTION. THE

BURGLAR ALARM SIGNAL SHALL NOT BE

CONNECTED TO A POLICE EMERGENCY

NUMBER.

1. In 2 (Printer DTR)

2. Ground

3. In 3 (4300 sync)

4. In 4 (4300 sync)

5. Ground

6. Out 5 (4300 data)

7. Out 6 (Printer RXD)

8. Ground

9. Ground

Red Jumper

(note 1)

DOC LOAD NO.: 5

J7 Header J8 Header

BATTERY

TABS

4192SD

SMOKE

WARNING: TO PREVENT

RISK OF ELECTRICAL

SHOCK, DISCONNECT

TELCO JACK BEFORE

SERVICING THIS PANEL.

THIS EQUIPMENT SHOULD BE INSTALLED

IN ACCORDANCE WITH THE NATIONAL

FIRE PROTECTION ASSOCIATION'S

STANDARD 72 (NATIONAL FIRE

PROTECTION ASSOC., BATTERYMARCH

PARK. QUINCY, MA. 02269). PRINTED

INFORMATION DESCRIBING PROPER

INSTALLATION, OPERATION, TESTING,

MAINTENANCE, EVACUATION PLANNING

AND REPAIR SERVICE IS TO BE

PROVIDED WITH THIS EQUIPMENT.

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.

Zone response time:

ZONES 1-8: 350mSec-500mSec

ZONE 9: Programmable for

Fast: 10mSec-15mSec

Normal: 350mSec-500mSec

(default response)

COMPLIES WITH FCC RULES, PART 68

FCC REGISTRATION NO. AC398U-68192-AL-E

RINGER EQUIVALENCE: 0.7B

THIS DEVICE COMPLIES WITH PART 15 OF

FCC RULES. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS: (1) THIS DEVICE

MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

(Refer to Installation Instructions for information concerning Direct Wire

Downloading and printer connections using the 4100SM Serial Module.)

Notes For UL Household Fire Installations

1. Use 12VDC, 14AH battery

2. Maximum auxiliary current,

including polling loop 300mA

3. Combined alarm and auxilary power output

and polling loop current must be limited to 750mA

for UL985 Household Fire Installations.

ALL CIRCUITS ARE

POWER LIMITED.

Blue

Jumper

(note 5)

5. Cut blue jumper to disable supervision of alarm sounder output.

Leave jumper intact to supervise output. (See Installation

Instructions for Programming and Wiring Instructions).

1 2 ... 246 247 248 249 250 251 252

Comments to this Manuals

No comments

ADEMCO VISTA-128B Setup Guide Page 251

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-128B