ADEMCO VISTA 10 Setup Guide download pdf (Page 15)

Section 2 – Installing the Control & Peripherals

2-7

Installing the 5881/5882 Receiver

RF System Installation Advisories

Follow the guidelines below when installing the RF

receiver. (Disregard

if the receiver is mounted in the

control cabinet.)

•

Place the RF receiver in a high, centrally located area

for best reception.

•

Do not locate the receiver or transmitters on or near

metal objects. This decreases range and/or blocks

transmissions.

•

Do not locate the receiver in an area of high RF

interference (revealed by frequent or prolonged

lighting of the LED in the receiver; random flicker is

OK).

TO CONTROL'S REMOTE KEYPAD

CONNECTION POINTS. EACH RECEIVER

MUST BE ON INDIVIDUAL HOME RUN.

USE MAX. of 220 ft. [67m of #22 (0.64mm)

WIRE or 550 ft. (168m) of #18 (1mm) WIRE

FOR EACH RUN]. OBSERVE 20 ft. MAX.

FOR COMMERCIAL FIRE INSTALLATIONS.

(SEE RECEIVER'S INSTRUCTIONS.)

DIP SWITCH WHITE AREAS = SWITCH

HANDLES. POSITIONS 2-4 DETERMINE

RECEIVER'S ADDRESS. CONSULT

CONTROL'S INSTRUCTIONS FOR

ADDRESS TO USE. DIP SWITCH BELOW

SHOWN SET FOR ADDRESS "0."

SWITCH

POSITION

RECEIVER ADDRESS SETTINGS

(" - " MEANS OFF)

0 1 2 3 4 5 6 7

PRESENT ONLY ON 5881EH (SEE TEXT AT LEFT)

ON ON ON

ONON

ONON ONON

ONON

FOR FUTURE USE

DIP SWITCH #5 (PRESET ONLY ON 5881EH)

ON: SETS 5881EH FOR USE IN COMMERCIAL

FIRE APPLICATIONS (SEE THE RECEIVER'S

INSTRUCTIONS)*.

OFF: USE IN NON-COMMERCIAL FIRE

INSTALLATIONS.

* FOR COMMERCIAL FIRE APPLICATIONS

THE 5881EH PC BOARD MUST BE MOUNTED

IN A SEPARATE CABINET (SEE RECEIVER'S

INSTRUCTIONS FOR DETAILS).

MOUNTING

HOLES

INSERT IN

RIGHT-HAND

TERMINALS

CIRCUIT

BOARD

DIP SWITCH

YELLOW

RED

BLACK

GREEN

INTERFERENCE

INDICATOR LED

WIRING

OPENING

PLUG & SOCKET

ANTENNAS

Figure 2-9. 5881/5882 RF Receiver

The RF receiver must be at least 10 feet from any

remote keypad to avoid interference from the

microprocessors in those units.

Installation and Setup of the 5881/5882 Receiver

o install the receiver, perform the following steps and

refer to Figure 2-9:

1. Set the receiver's DIP switches for device address 0,

(all switches are in the OFF position).

2. Mount the receiver. The RF receiver can detect signals

from transmitters within a nominal range of 200 feet.

Take this into consideration when determining

mounting location.

3. Connect the receiver's wire harness to the control's

keypad terminals (4, 5, 6, and 7). Plug the connector

at the other end of the harness into the receiver.

4. Refer to the installation instructions provided with

the receiver for further installation procedures

regarding antenna mounting, etc.

In Canada

, 5800 systems must use 5882

Series receivers. Information relative to the

5881 Series of receivers applies as well to the

5882 Series. 5881 and 5882 Series receivers

can support the same 5800 type transmitters.

Any zone

number

from 10–25 can be used as

a 5800 Series wireless zone.

Jam Detection and Reporting

When field

✱

22, option 4 (RF SYSTEM) is selected, a

5800 Series receiver detecting a jam condition sends an

E344

(RF Receiver Jam Detect) Contact ID

report to the

central station. At the same time, a

Rcvr Jam

(on alpha

keypads) or

CHECK 90

(on fixed-word keypads) message

alternates with the present system message on the

keypad.

When the jam condition is cleared, a

Restore

message is

sent to the CS. Entering a code and OFF restores the

keypad display.

The default for this option is 0 (disabled).

RF Jam Detection must be enabled for UL

installations using wireless devices.

Note:

when RF jam detection is selected, an RF receiver

will detect a condition that may impede proper RF

reception (i.e., jamming or other RF interference). Such a

condition will produce a message display, and a report

will be sent to the central monitoring station (if trouble

reporting is enabled).

Normal use of a 5827 wireless keypad may

cause a false RF jam message to be displayed

in systems that have been programmed for RF

Jam Detection.

Receiver Supervision

The receiver is supervised. The following conditions cause

a Trouble report to be generated and

CHECK

and

ZONE

messages to be displayed:

•

Communication between the panel and the receiver is

interrupted.

•

No valid RF signals from at least one supervised

wireless transmitter are received within 12 hours.

House Identification

If you are using a 5804BD, 5827, or 5827BD Wireless

Keypad with the system, you must program a House ID

Code (01-31) in field

✱

24 to establish proper

communication. The keypad must be set to the same ID.

House ID set to 00 disables

all

wireless keypads.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 79 80

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 15

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10