ADEMCO Vista-128FB Setup Guide Page 59
- Page / 147
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3 - Installing the Control
3-35
Connecting the Transformer
This product uses the 1361 transformer (1361CN in
Canada). If you are using X-10 devices, the 1361X10
transformer interface must be used instead of the
regular 1361 transformer. The 1361X10 supplies the
control panel with AC, and also sends control pulses
through the premises’ electrical system to control the
X-10 devices.
U
L
Use 1361CN Transformer in Canadian
installations.
Power Limiting Outputs
All outputs are power-limited as per UL985/UL1023.
The following table shows the maximum current that
may be drawn from each output.
Output Maximum Current
Draw
Auxiliary Power 750mA
Polling Loop 128mA
Alarm Output 1.7A
For Household Fire or Combination Household
Fire/Burglary Installation: The total current drawn
from the auxiliary power, the polling loop, and the
alarm output combined must not exceed 750mA to
comply with the battery independence requirements in
UL985.
For Household Burglary-Only Installations: The
total current drawn from the alarm output may be up
to 1.7A. A battery must be installed to supply the
current of the combined auxiliary power, polling loop,
and alarm output in excess of 750mA.
Failure to observe the polling loop current
rating will cause polling loop malfunction.
Failure to observe the auxiliary power current
rating will result in a battery that does not
charge properly or possibly a tripped circuit
breaker.
To connect the transformer to the control, perform the
following steps:
Step Action
1 Connect all installed devices to the control.
2 Wire the 1361 Transformer (1361CN in
Canada) to the panel (before connecting the
battery) as shown in Figure 3-42, or wire
the 1361X10 Transformer as shown in
Figure 3-43 (if using X-10 devices).
3 Plug the transformer into a 24-hour,
uninterrupted, 120VAC, 60Hz outlet. After
a few seconds, the keypad display appears.
NO CONNECTION
TRANSFORMER
16.5VAC, 40VA
ADEMCO No.1361
or 1361X10, if X-10
DEVICES WILL BE USED.
Connect to
24hr. source
of AC mains
123
RED (+)BLK (-)
Connect to
12VDC, 4AH
or 12VDC, 7AH
GEL CELL
BATTERY
CHARGING
VOLTAGE
13.7VDC
NOTE:
WHEN POWERING UP
THE PANEL, PLUG THE
TRANSFORMER IN BEFORE
CONNECTING THE BATTERY.
BATTERY
TABS
PRIMARY POWER
Supplied by a transformer
which is rated at
16.5VAC, 40VA.
Caution must be taken when
wiring this transformer to the
panel to guard against blowing
the fuse inside the transformer
(non-replaceable).
pwr_bat_conn-001-V1
Figure 3-42: 1361 Transformer and Battery Connections
123456789
BLACK
BLUE
BROWN
GREEN
RED
WHITE
YELLOW
GRAY
VIOLET
4142TR CABLE
X10 TRANSFORMER/INTERFACE
TERMINALS
ON CONTROL
BOARD
1361X10-001-V0
J8 CONNECTOR
Figure 3-43: 1361X10 Transformer Connections
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Related products and manuals for Security access control systems ADEMCO Vista-128FB
(5 pages)
(76 pages)
(24 pages)© 2020, manymanuals.com. All rights reserved. | 2.895 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals