ADEMCO VISTA-100 Service Manual download pdf (Page 47)

LOCAL TEST MODE:

Prior to installation the local test mode should be performed.

With only power applied to the FSA module, press any button

within 3 seconds. All LEDs will light and the sounder will beep,

then all LEDs will sequentially light and turn off. The sounder

will beep once at the end of the test.

INSTALLATION:

For UL Installations: Mount the FSA module horizontally to a

duplex box (quad box for FSA-24). All wiring between the FSA

module and the control must be run in conduit.

CONNECTIONS AND SETTINGS:

Select and set an address for the FSA module, using its DIP

switch as shown in the table below. Each FSA module used

with the control must be assigned a unique address so the

control can identify the FSA module and communicate with it

properly. The address to be set is determined by the particular

control to be used, and the control's installation instructions

must be consulted.

Connections to the control's keypad wiring points are made

via 5-position terminal block TB1, a 5-pin plug or both (wire

color connections are the same).

TO ENABLE THE FSA UNIT:

• At the control panel keypad, from the Data Field

Programming Mode, press #93 to display “ZONE PROG”.

Press 0 repeatedly to display the “DEVICE PROG?”

prompt. Press 1 to enter Device Programming.

• The “DEVICE ADDRESS” prompt is displayed. The device

address identifies the device to the control. Enter the

2-digit FSA module address number to match the physical

address of the FSA module DIP switch settings (08-23).

Up to 4 FSA modules can be installed in the system. Each

requires a unique device address.

• Press [(] to accept entry. The “DEVICE TYPE” prompt is

displayed. Enter 8 = Fire Display.

• Press [(] to accept entry. The “RST FIRE PTN?” prompt is

displayed.

• Enter 0 to disable the FSA’s Silence/Reset button (default

mode).

• Enter 1 to enable the FSA’s Silence/Reset button to

Silence the fire alarm system when pressed once.

(Silence only)

•

Enter 2 to enable the FSA's Silence/Reset button to

Silence and then Reset the fire alarm system when pressed

twice.

Requires the approval of the AHJ.

Please Note: When the installation is Fire/Burg, a Burg

Zone should not be Installed (or enrolled) in the Fire

partition (partition 1). It will be Reset with a “Fire Reset”

and the system will lose Burg security.

• Press [(] to accept entry. Be sure to set the FSA module

DIP switches to match the Device Address you have

enabled.

TO PROGRAM THE LEDS:

• At the control panel keypad, from the Data Field

Programming Mode, press #93 to display “ZONE PROG”.

• Press 0 repeatedly to display the “OUTPUT PROG?”

prompt.

• Press 1 to enter Output Programming. The “ENTER RELAY

#” prompt is displayed.

• Enter the 2-digit Relay / Output # (01 – 96). OR Enter 00

to Quit (00 = Quit).

• Press [(] to accept entry. Refer to the control panel

installation and programming guide relay programming

section. Program the LEDs as if they were relays selecting

zone number, list, or type, start/stop instructions, etc. until

the “RELAY TYPE” prompt is displayed. At this prompt

enter 3 = FSA.

•

Press [(] to accept entry. The “ECP ADDRESS” prompt is

displayed. Enter the 2-digit ECP address of the FSA.

•

Press [(] to accept entry. The “LED #” prompt is displayed.

Enter the LED number to be associated with the zone

number, type, or list previously programmed.

• Press [(] to accept entry.

•

Repeat for all LEDs at “ENTER RELAY #” prompt.

SYSTEM TEST MODE:

With the system installed and programmed, press the TEST

button. All LEDs will light and the sounder will beep, then all

LEDs will sequentially light and turn off. The sounder will beep

once at the end of the test.

FSA-8/FSA-24

Fire System Annunciator

00000

ECP Bus

Dip Switch

Optional

Keyswitch

Connection

SIDE

VIEW

All Switches shown

in Up position.

(ECP Address 23)

Terminal

Block

Connect to

Keypad

Terminals

DIP

Switch

Position

ECP Address

Down

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

ORDERING:

Part No. Description

FSA8 Fire Annunciator

FSA24 Fire Annunciator

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 79 80

Comments to this Manuals

No comments

ADEMCO VISTA-100 Service Manual Page 47

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-100