ADEMCO VISTA-250FBP Setup Guide download pdf (Page 103)

Section 9 – User Access Codes

9-3

Adding a Master, Manager, or Operator Code

During user code entry, normal key

depressions at other keypads in a partition are

ignored. However, panic key depression

causes an alarm and terminates user entry.

Enter Installer Code

†

+ [8] + new user no. (002-250) +

new user’s code

†

Or Master or Manager Code, but the

code must be a higher level of authority than the code

being changed (e.g., a Manager Code can add an

Operator-level Code, but cannot add a Master or

another Manager Code). Keypad prompts for the

authority level for this user.

NOTE: All references to the number of user codes

pertain to the VISTA-250FBP. The VISTA-128FBP

allows only 150 user codes.

PROMPT

EXPLANATION

User Number = 003

Enter Auth. Level

Enter the level number as follows:

1 = Master

2 = Manager

3 = Operator A

4 = Operator B

5 = Operator C

6 = Duress

Keypad then prompts for Open/Close reporting option for this user.

Open/Close Rep.?

0 = NO , 1 = YES

Press 0 (NO) or 1 (YES), depending on whether or not arming/disarming by this user will trigger

Opening and Closing reports. This prompt appears only if the Installer Code is used to add a

user.

Group Bypassing?

0 = NO , 1 = YES

Enter 1 (YES) to allow this user to perform group bypasses. Enter 0 (NO) this user will not be

able to perform group bypasses.

NOTE: In addition to enabling the user for group bypassing, the user must also have access to

the partition(s) containing the zones being bypassed and have global arming capability.

Access Group?

Enter 0-8

If access schedules have been programmed, this prompt appears. Enter the user’s access

group number (1-8) if this user should have limited access to the system. Enter 0 if no access

group should be assigned.

RF Button ?

0=NO , 1=YES

Not Used.

Multi-Access ?

0 = NO , 1 = YES

Press 0 (NO) if the user is to have access to this partition only. Press 1 (YES) if the user is to

have access to more than one partition. If NO, the program exits this mode. If YES, the keypad

prompts for the Global Arm option for this user.

Global Arm ?

0 = NO , 1 = YES

Press 0 (NO) or 1 (YES), depending on whether this user will be allowed to arm more than one

partition via Global Arm prompts (described in the

VISTA-128FBP/VISTA-250FBP User Guide

The keypad now prompts for the user’s access to the next partition.

Part. 2 – SHOP ?

0 = NO , 1 = YES

Press 0 (NO) or 1 (YES), depending on whether this user will have access to the displayed

partition number. If NO, the keypad displays this prompt for the next partition number in

sequence.

If YES, the keypad prompts for the following:

• User’s authority level in the displayed partition (see Authority Level prompt above).

• Open/Close option for this user in the displayed partition (see Open/Close prompt above).

• Global Arm option for this user in the displayed partition.

When all partitions have been displayed, the keypad will scroll through all partitions to which

access has been assigned, and will display the user number, authority level, open/close and

global arm options that were programmed for each partition to which the user was granted

access. For example:

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 135 136

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 103

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP