ADEMCO VISTA-250FBP Setup Guide download pdf (Page 106)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

10-2

PROMPT

EXPLANATION

AUTO-TEST DET?

0=NO 1=YES

Enter 1 (YES) to have the system automatically test all polling loop points with a fire response type 9 or 16.

Other fire zones will have to be tested manually.

Enter 0 (NO) to test every point manually.

The next prompt will be displayed.

For true detector sensitivity tests, and for compliance with fire codes, you must enter 0 (NO) to this question.

LOG RESULTS?

0=NO 1=YES

Enter 1 (YES) to have the system log each point as it is tested. A list of untested points will also be logged.

Enter 0 (NO) if you do not want to log the results.

The next prompt will only be displayed if Contact ID report format has been selected.

C.S. TRANSMIT?

0=NO 1=YES

Enter 1 (YES) to have the results of the test sent to the central station. This report will consist of a list of

points that have been tested followed by a list of points that have not been tested.

Enter 0 (NO) if you do not want to report the results. A Walk-Test Start and Walk-Test End report will be

sent in either case (if programmed).

When the Test Mode is activated, the system will sound

fire Notification Appliance Circuits (or any NAC having

a non-zero response type programmed in the #93 Menu

Mode) for 3 seconds. The system will also send a Start

of Walk-Test message to the central station, and will

light all keypad indicators (except the ARMED LED)

and display window segments to verify that they are

working properly. The keypads will then display Fire

Walk-Test in Progress and will sound a single beep

every 15 seconds while this test is active. Additionally,

in this test mode RF receiver sensitivity is reduced to

50% to ensure proper fire RF device mounting locations.

The system will build a list of all the fire zones

(response types 9, 16, 17, 18) that need to be tested.

These points will be scrolled on the display. For each

point, the keypad will display "UNTST XXX," where

XXX is the point number, followed by an alpha

descriptor for the point.

If the auto-test option has been selected, the control

panel will attempt to automatically test all of the

polling loop points that have a zone response type of 9

or 16. For points that must be manually tested, fault

and reset each fire alarm sensor in turn.

Each action should cause keypads to beep and fire

Notification Appliance Circuits to ding. The keypads

will display the zone number and the associated alpha

descriptor while the zone remains faulted. The system

automatically issues a smoke detector power reset

about 10 seconds after it finds a fault on one of these

zones, to allow faulted detectors to be reset.

The system will automatically perform the

smoke detector reset on zones 1 and 2, if

programmed for fire, and on the auxiliary relay

and any other output device (relay) that is

programmed for smoke detector reset.

To end the test, enter any security code and press OFF.

An End of Walk-Test message will be sent to the central

station (if programmed). Note that the test will

automatically end if no faults are detected within a 1-

hour time period.

Burglary Walk-Test (

This test causes the system to sound keypad beeps in

response to faults on zones for the purpose of allowing

proper zone operation to be checked without triggering

alarms. This test can be activated by any user by

entering the corresponding security code and pressing

TEST while the burglary portion of the system is

disarmed. UL requires that this test be conducted on a

weekly basis.

When this test is first entered, the system activates the

alarm output for 3 seconds. The system sends a Start of

Walk-Test message to the central station. The keypad

displays “Burg Walk Test in Progress” and sounds a

single beep every 15 seconds while the test remains

active.

Open and close each protected door and window in turn.

Each action should produce three beeps from the

keypad. Walk in front of any motion detectors. Listen

for three beeps when the detector senses movement.

The keypad displays the zone number and alpha

descriptor while a door or window remains open or

while a detector remains activated. The system

automatically issues a Zone 8 Glassbreak Detector

Power Reset about 10 seconds after it finds a fault on

this zone, to allow faulted detectors to be reset.

To end this test, enter any security code and press OFF.

An End of Walk-Test message is sent to the central

station.

1 2 ... 101 102 103 104 105 106 107 108 109 110 111 ... 135 136

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 106

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP