ADEMCO VISTA-250FBP Setup Guide download pdf (Page 78)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

5-14

FIELD TITLE and DATA ENTRIES EXPLANATION

3*00

Check or TRBL Display

0 = CHECK

1 = TRBL

Select whether the system should display CHECK or TRBL when a trouble

condition occurs.

3*01

Event Display Lock

0 = disable

1 = enable

If enabled, the system locks the display on the first fire alarm. Press

✳ to

display the next fire alarm in the system. If disabled, the system scrolls all

alarms automatically.

When 3*01 is Enabled, the following priorities go into effect:

The First event to occur is locked on the display; subsequent events will be

displayed in priority order:

Priority 1: Life Safety: ZT 06, 07, 09, 16, 17, and Duress override all other s

below

Priority 2: Property Safety: ZT 01, 02, 03, 04, 05, 10 override all other s below

Priority 3: Supervisory: ZT 14, 18, 19 and Fire Trouble override all other s

below

Priority 4: System: AC Loss, Low Bat, Line Cut, etc. do not override any other

events

NOTE: Must be set to “1” for Commercial Fire installations.

3*12

Zone Type 18 Delay Use

0 = disable

1 = enable

If enabled, use the delay time programmed in field 3

✳16.

3*13

Fire Supervisory Response to

Open/Short (Applies to Zone

Type 18)

0 = disable

1 = enable

If “0” is selected, the system will respond with a trouble on open, and a

supervisory on short.

If “1” is selected, the system will respond with a supervisory on open, and a

supervisory on short.

Must be set to “0” for Commercial Fire and Commercial Burglary installations.

3*14

Waterflow Alarm Silence Option

0 = silenced by User Code + OFF

1 = silenced when zone restores

Select how the Waterflow zone type will be silenced.

NOTES:

This feature may be set to 1 only by permission of the local authority.

For an output of a 4204CF to be silenced when 3*14=1, all Type 17

(Waterflow) zones activating the output must be put into a Zone List, and that

Zone List must be the STP condition of the 4204CF fire output. In addition to

the STP ZL, you also need an STP ZT of 22 in order to silence via code + off

in the event the zone does not restore.

Since a Type 17 zone is processed as a FIRE alarm, it will activate outputs

programmed for STT ZT 17, 16, 09, and 39. The only way to have individual

output activations (e.g. ZT17 versus ZT09) is to use zone lists.

NOTE: Must be set to “0” for Commercial Fire installations.

3*16

Zone Types 17 & 18 Delay

Enter 01-15 times 2 seconds

Enter 00 for no delay

Select the delay time for zone types 17 and 18. The zone must be faulted for

entire delay time before an alarm or supervisory condition occurs. This may

prevent alarms due to minor fluctuations in waterflow.

Maximum combined delay of3*16 and 3*18 cannot exceed 90 seconds for UL

installations.

NOTE: Must be set to “00” for Commercial Fire installations.

3*17

Zone 6 Alternate Function Enable

0 = disable

1 = enable

If enabled, zone 6 may be used as a tamper zone (bell and cabinet tampers).

If used, the zone will annunciate in accordance with response type, rather

than a ground fault when a ground fault is detected.

3*18

Extended Delay for Zone Types

17 & 18

0 = no extended delay

1 = multiply delay by 4

This option allows the delay programmed in field 3

✳16 for Waterflow and

Supervisory zones to be extended by 4 times.

NOTE: Must be set to “0” for Commercial Fire installations.

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 135 136

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 78

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP