ADEMCO VISTA-250FBP Setup Guide download pdf (Page 81)

6-1

SECTION 6

Scheduling Options

•••••••••••••••••••••••••••••••••••••••••••••••••

• You must program Bypass and Auto-Arm Fail reports for UL installations.

• Auto-disarming is not permitted in UL installations.

• You must not program Random Scheduling of Time Driven Events for UL installations.

General

The scheduling features allow certain operations to be

automated, such as arming, disarming, bypassing of

zones, and activating relay outputs.

The system uses time windows (a programmed period of

time with a start and stop time) for defining open/close

schedules, holiday schedules, user-defined temporary

schedules, and access schedules for users.

Scheduled events are programmed by user-friendly

menu modes of programming (#80, #81, #83, and #93

modes), explained in detail in this section. These menus

take you step by step through the options.

Auto Arming

The system can automatically arm (AWAY Mode) a

partition at the end of a pre-determined closing

(arming) time window.

Auto Arming can be delayed three ways: by use of the

Auto-Arm Delay, the Auto-Arm Warning, or by

manually extending the closing (arming) time window

with a keypad command.

The system can also automatically bypass any open

zones when auto arming.

Auto-Arm Delay

Auto-Arm Delay provides a delay (grace period) before

auto arming. It starts at the end of the closing time

window.

The delay is set in 4-minute increments, up to 56

minutes in partition-specific program field 2*05. At the

expiration of this delay, the Auto-Arm Warning will

start.

Auto-Arm Warning

The Auto-Arm Warning causes the keypad sounder to

warn the user of an impending Auto-Arm.

The warning can be set from 1 to 15 minutes prior to

the arming in partition-specific program field 2*06.

During this period the keypad beeps every 15 seconds

and displays “AUTO ARM ALERT.” During the last 60

seconds, the keypads beep every 5 seconds.

The panel arms at the conclusion of the Auto-Arm

Warning period.

Extend Closing Window

A user can manually delay the arm (closing) time

window by 1 or 2 hours. This is done by entering a

keypad command (User Code + #82), which then

prompts the user to enter the desired extension time of

1 or 2.

This feature is useful if a user must stay on the

premises later than usual.

The Auto-Arm delay and warning periods begin at the

end of the extension.

Force Arm

The Force Arm option causes the panel to attempt to

bypass any faulted zones prior to auto arming (panel

performs a force-arm).

This option is set in partition-specific program field

2*08.

Auto Disarming

The system can automatically disarm a partition at the

end of a pre-determined opening (disarm) time window.

The disarming time can be delayed by using the Auto-

Disarm Delay feature.

Disarm Delay

Auto-Disarm Delay provides a delay before auto

disarming. This delay is added to the end of the disarm

time window.

The delay is set in 4-minute increments, up to 56

minutes, in partition-specific program field 2*07.

Restrict Disarming

This option allows disarming by users only during the

disarm time window and during the arming time

window (in case user needs to re-enter premises after

manually arming the partition).

This option is set in partition-specific field 2*10. If field

2*10 is set, we highly recommend setting field 2*11, as

well. This field allows the partition to be disarmed

outside the arm/disarm time windows only if the

partition is in alarm.

1 2 ... 76 77 78 79 80 81 82 83 84 85 86 ... 135 136

Comments to this Manuals

No comments

ADEMCO VISTA-250FBP Setup Guide Page 81

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA-250FBP