ADEMCO VISTA-250FBP Setup Guide Page 30
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
VISTA-128FBP/VISTA-250FBP Installation and Setup Guide
3-8
Supervising the Notification Appliance Circuits
To wire the NAC using the supervision feature, perform the following:
Install a 2K EOL resistor (Model 2EOL, supplied) across the last notification appliance on each Notification Appliance
Circuit to be supervised.
Auxiliary Relay Connections
The VISTA-128FBP/VISTA-250FBP provides a built-in Form C relay with contacts rated at 28VAC/VDC, 2.8A. The relay
may be programmed (field 3
✳61) for one of the following functions:
• Alarm Activation
• Trouble/Supervisory Activation
• 4-Wire Smoke Detector Reset
• Battery Saver
Alarm Activation
(3
✳61 = 1 or 4) Steady activation in response to an alarm.
If field 3
✳61 = 1, the auxiliary relay remains active until Aux. Relay Timeout expires or until User Code + OFF is
entered. This option can be used to provide an unsupervised Notification Appliance Circuit for supplementary strobes,
sounders, etc. when wired to the Aux Power 1 or a separate power supply, see Figure 3-8.
If field 3✳61 = 4, the auxiliary relay remains activated until User Code + # + 67 is entered. By default, the relay is set
to activate on alarm zones 1-8 with no timeout (field 3
✳61 = 1).
When field 3✳61 = 1, the auxiliary relay can be programmed to give a brief activation for confirmation of arming ding
(field 3
✳57) or Chime Mode (field 3✳59).
NOTES:
USE NON-POLARIZED INDICATING DEVICES.
WIRING IS NOT SUPERVISED.
DO NOT EXCEED RATINGS OF THE SUPPLY USED.
IF AUX. PWR. 1 OUTPUT IS USED, THE COMBINED
ALARM CURRENT DRAIN FROM AUX. PWR. 2,
BELL 1, AND BELL 2 CANNOT EXCEED 2.3A MAX.
belloutput-005-V0
812117
AUX RELAY FACTORY DEFAULTS
ACTIVATES FOR ZONES 1-8 ALARMS
(STEADY ALARM OUTPUT).
NO TIMEOUT.
109
+
AUX PWR #1
GROUND
POLE
N.O.
N.C.
CAN DRAW POWER FROM
AUX. PWR. 1 OUTPUT OR
FROM SEPARATE SUPPLY.
ALARM
Figure 3-8: Wiring Auxiliary Relay for Alarm Activation
Trouble/Supervisory Activation
(3
✳61 = 0) Steady activation in response to any zone or system related trouble condition or to any fire supervisory
condition. The auxiliary relay remains activated until all fault conditions have been corrected and a User Code + OFF
is entered.
4-Wire Smoke Detector Reset
(3
✳61 = 2) Momentary (8-second) activation in response to a second entry of a User Code + OFF sequence following a
fire alarm condition. This interrupts power to 4-wire smoke detectors connected to hardwired zones 1-8 and polling loop
zones, allowing the detectors to be reset. Power to the detectors should be wired to the auxiliary relay and to Aux. Power
1 output, see Figure 3-9.
Battery Saver
(3✳61 = 3) When this option is selected, the auxiliary relay is normally activated (e.g., N.O. and pole contacts are
connected) and de-activates 4 hours after the start of AC Loss. Using this feature, non-critical loads, such as
supplementary keypads, can be disconnected from the auxiliary power outputs, allowing a smaller capacity battery to be
used. The relay re-activates within a few seconds after the AC power restores.
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Related products and manuals for Security access control systems ADEMCO VISTA-250FBP
(54 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.675 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals