ADEMCO VISTA-250FBP Setup Guide Page 9
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ix
UL864 (Commercial Fire) Compliance
•••••••••••••••••••••••••••••••••••••••••••••••••
General Requirements
The VISTA-128FBP/VISTA250FBP control panels provide features that allow the system to meet UL864 Commercial
Fire requirements. To meet these requirements, follow the guidelines outlined in this section.
• The reporting of bypassed points to the central station must be enabled in Report Code Programming mode.
• Fire alarm notification circuits must be supervised (e.g., supervisory zones 970 and 971 for Bell 1 and Bell 2 outputs)
• Only one relay of the 4204CF can be programmed for a NAC. If the 4204CF relay is programmed as a NAC, the stop
action must be programmed as a zone type 62, Bell 2 Timeout.
• Output devices are not intended for overriding automatic fire and building functions.
• Line cut detection must be enabled for both the main and backup phone lines (supervisory zones 974 and 975).
• Access Control Devices cannot be used.
• Audio Alarm Verification Devices cannot be used.
• Remote downloading can only be performed if a service person is at the premises.
• All supervision zones for the polling loop, RF receivers, keypads, NAC outputs, and telephone lines that are used, must
be enabled as zone type 19 (24-hour trouble).
Programming Field Settings for UL864 Compliance
NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER INVOLVED
PARTIES
This product incorporates field-programmable software. In order for the product to comply with the requirements
in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features
or options must be limited to specific values or not used at all as indicated below.
Program feature or option Permitted in
UL864? Y/N
Possible settings Settings permitted in UL 864
✱
08 TEMPORAL SIREN
PULSE
N
0 = disable
1 = enable
Not used at this time. Must
be set to “0” (disable).
✱
13 ALARM SOUNDER
(BELL) TIMEOUT
Y Enter 01-15 multiplied by 2
minutes. 00 = no timeout.
Must be set to “3” (Minimum
of 6 minutes).
✱
14 TRIGGER OR RS232
N
0 = trigger
1 = RS232 input
Must be set to “0”.
✱
17 AC LOSS KEYPAD
SOUNDING
N
0 = disable
1 = enable
Must be set to “1” (enabled).
✱
20 VIP MODULE
PHONE CODE
N 1-9 = first digit of access code
∗ or # = second digit of access
code (enter # +11 for “∗”, or #
+12 for “#”).
To disable enter 0 for the 1
st
digit.
Not used.
Must be set to “00”.
✱
22 KEYPAD PANIC
ENABLES (PARTITION
SPECIFIC)
N
0 = disable
1 = enable
Must be set to “000” for
partition 1 in fire systems.
✱
23 MULTIPLE
ALARMS (PARTITION
SPECIFIC)
N 0 = disable
1 = enable
Must be set to “1” (enabled).
✱
26 INTELLIGENT TEST
REPORTING
N
0 = disable
1 = enable
Must be set to “0” (disable).
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Related products and manuals for Security access control systems ADEMCO VISTA-250FBP
(54 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.543 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals