ADEMCO VISTA 10 Setup Guide Page 15
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
U
L
A UL Listed keyswitch is required for fire
installations and UL commercial and residential burglar
alarm installations.
If a keyswitch is used on:
• an installation that transmits opening and closing
signals, the keyswitch zone must be programmed to
send opening and closing signals.
• a UL commercial burglar alarm installation, the
keyswitch’s tamper switch must be connected in to
the alarm system. This tamper switch zone must
also be programmed for Zone Type 05 – Trouble by
Day / Alarm by Night.
• a fire alarm installation, the keyswitch must be
located next to an alphanumeric display keypad.
The Ademco 4146 keyswitch is UL Listed.
4146 KEYSWITCH
(READY)
GREEN
LOCK
SWITCH (N. O.)
TAMPER
SWITCH (N. C.)
(ARMED)
RED
YELLOW
WHITE
EOLR
(use appropriate value)
11
10
TYPICAL ZONE
ON CONTROL
BOARD
BROWN
BLUE
BROWN
BLUE
820
ohms
820
ohms
00-trigcon-004-V3
1345
4-WIRE
CABLE
5-PIN TRIGGER CONNECTOR
KEY
+12 AUX.
OUTPUT 17
OUTPUT 18
(RED)
(YELLOW)
(GREEN)
RED
BLACK
Figure 10. Keyswitch Wiring Connections
Connecting Relay Modules
1. Mount either remotely or in the control panel.
2. Connect to control’s keypad terminals using the connector harness supplied with the module. Use
standard 4-conductor twisted cable for long wiring runs.
3. Set the module’s device address to address 12.
4. Connect the desired field wiring to the unit's relay contact terminals.
NOTES
• Use 4204 module.
• Supervision: 4204 module is supervised against removal. The module’s device address is displayed
as follows if a module is disconnected from the control’s terminals, or if the module cover is removed
and the tamper jumper is installed:
Alpha: CHECK xx Wire Expansion
FAULT xx Wire Expansion
ALARM xx Wire Expansion
Fixed-Glass: lxx (or 91 if field *199 set for 2-digit display); where “xx is the module’s address.
• If communication/tamper failure occurs on a device with zones wired to it, all zones on the device
will be displayed.
U
L
For UL installation requirements, refer to the
Installation Instructions for the 4204.
TB2
121110
9
87654321
(–) GROUND
(+) 12V
YEL
BLK
GRN
RED
13 14 15 16
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
COVER TAMPER (REED) SWITCH
TB1
4204
4-PIN TOUCHPAD PLUG
3
2
RELAY
1
4
TYPICAL
(SHOWN "OFF")
C
NC
NO
C
NC
NO
C
NC
4204_conn-1-V0
NC
NO
C
NC
NO
EITHER OR BOTH
CAN BE USED
DATA IN
FROM CONTROL
DATA OUT
TO CONTROL
RELAY
RELAY
RELAY
Figure 11. 4204 Connections to Control
Mounting and Wiring the Control
2-9
- ADEMCO VISTA-10P 1
- ADEMCO VISTA-10PSIA 1
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 5
- SECTION 2 7
- Cabinet and Lock 7
- DETAIL A 8
- DETAIL B 8
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Wiring the AC Transformer 10
- Backup Battery 10
- Earth Ground 11
- Hardwire Zones 12
- Smoke Detectors 12
- Installing a 5800TM Module 13
- Installing the RF Receiver 13
- Installing the Transmitters 14
- Installing a Keyswitch 14
- 4204_conn-1-V0 15
- On-Board Triggers 16
- Long Range Radio Connections 17
- 4285/4286 18
- Programming Overview 19
- Pager Programming 20
- Function Keys 20
- Output Devices 20
- Zone Type Definitions 21
- Mechanics of Programming 23
- Table of Device Addresses 24
- Installation Instructions 24
- Data Field Programming 25
- Dialer Programming 27
- System Status Report Codes 28
- Miscellaneous System Fields 30
- Pager Programming Fields 32
- Zone Conditions Represented 34
- Keypad Programming Fields 35
- Menu Mode Programming 37
- 02 HARDWIRE TYPE 38
- ✱ TO SKIP 38
- TO CONFIRM? 39
- AXXX-XXX – 40
- These transmitters 41
- Zone List Overview (∗ 45
- ∗81 Menu Mode) 45
- Zone List Programming 45
- ∗57 Menu Mode) 46
- Programming Function Keys 46
- (For Adding Custom Words) 49
- HH MMAM 0010000 51
- 0=NO 1=YES X 51
- SECTION 6 53
- Report Code Formats 53
- Ademco Contact ID 55
- User Security Codes 56
- Setting the Real-Time Clock 56
- Keypad Functions 57
- Panic Keys 58
- Power Failure 58
- Testing the System 59
- Go/No Go Test Mode 60
- SECTION 8 61
- SECURITY CONTROL 61
- COMPATIBLE DEVICES 61
- Regulatory Agency Statements 65
- UL NOTICES 66
- Limitations and Warranty 67
- – INDEX – 69
- SUMMARY OF CONNECTIONS 71
- ÊK0735V3^Š 72
Related products and manuals for Security access control systems ADEMCO VISTA 10
(68 pages)
(64 pages)InSinkErator SS-50 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek InSinkErator SS-50.
Dostarczamy 1 pdf podręczników InSinkErator SS-50 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comments to this Manuals