ADEMCO VISTA 10 Setup Guide Page 58
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Panic Keys
There are three Panic keys (A, B, and C) that, if programmed, can be used to manually initiate
alarms and send a report to the central station by pressing and holding the appropriate key for at
least 2 seconds. Each key can be programmed for 24-hour Silent, 24-hour Audible, Fire, or Personal
Emergency responses. The Panic keys are identified by the system as follows:
Keys Displayed as Zone
[A] (∗/1)
95
[B] (∗/#)
99
[C] (3/#) 96
IMPORTANT: For a Silent panic function (if programmed) to be of
practical value, you must program a report code for the zone and the
system must be connected to a central station.
Various System Trouble Displays
Alpha Display Fixed Disp. Meaning
ALARM CANCELED CA will appear if an exit or interior zone contained a fault during closing at the time
the Exit Delay ended (e.g., exit door left open), but the system was disarmed during
the Entry Delay time. The alarm sounder and keypad sound continuously, but stop
when the system is disarmed. No message will be transmitted to the central station.
EXIT ALARM EA will appear when the Exit Delay ends if an exit or interior zone contained a fault
during closing. The alarm sounder and keypad sound continuously until the system
is disarmed (or timeout occurs). An “Exit Alarm” message is sent to the central
station.
Also results if an alarm from an exit or interior zone occurs within 2 minutes after
the end of an Exit Delay.
CHECK CHECK indicates that a problem exists with the displayed zone(s) and requires attention.
ALARM 1xx 1xx indicates that communication between control and a zone expander or wireless
FAULT 1xx 1xx receiver is interrupted, where “xx” is the device address. Check the wiring and
CHECK 1xx 1xx DIP switch settings on the units.
91 If field *199 is set to “1,” all ECP module problems are displayed as “91.”
If there are wireless sensors in the system, the Check condition may also be caused
by some change in the environment that prevents the receiver from receiving
signals from a particular sensor.
SYSTEM LO BAT BAT with no zone number indicates that the system's main standby battery is weak.
LO BAT BAT with a zone number and a once-per-minute beeping at the keypad indicates that a
low-battery condition exists in the wireless sensor displayed (zone “00” indicates a
wireless keypad). If the battery is not replaced within 30 days, a “CHECK” display
may occur.
NOTE: Some wireless sensors use a non-replaceable long-life battery which requires
replacement of the entire unit at the end of battery life (e.g., 5802, 5802CP).
Busy-Standby dl If this remains displayed for more than 1 minute, the system is disabled.
Modem Comm CC The system is in communication with the central station for change of function or
status verification.
no display no display Power Failure
If there is no keypad display at all and the LEDs are unlit, operating power (AC and
battery) for the system has stopped and the system is inoperative.
If the message “AC LOSS” (Alpha display keypads) or “NO AC” (Fixed-Word display
keypads) is displayed, the keypad is operating on battery power only.
If the battery standby capacity is used up during a prolonged AC power outage, the
control's power will shut down to minimize deep discharge of the battery.
Comm. Failure FC A communication failure has occurred.
Open Circuit OC The keypad is not receiving signals from the control and sees an open circuit.
Long Rng Trbl bF Backup LRR communication failure.
Bell Failure 70 Bell supervision failure.
RCVR Jam 90 RF jam detected.
KEYPAD LOW BAT 00 BAT Wireless keypad low battery
Phone Okay Cd The dialer test has been successful (CID code 601).
Dialer Off dO The dialer is disabled.
Test in Progress dd Walk test mode is active(CID code 607).
Upload Completed dC The upload or download session was completed.
Upload Failed dF The upload or download session failed before completion.
Installation Instructions
6-6
- ADEMCO VISTA-10P 1
- ADEMCO VISTA-10PSIA 1
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 5
- SECTION 2 7
- Cabinet and Lock 7
- DETAIL A 8
- DETAIL B 8
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Wiring the AC Transformer 10
- Backup Battery 10
- Earth Ground 11
- Hardwire Zones 12
- Smoke Detectors 12
- Installing a 5800TM Module 13
- Installing the RF Receiver 13
- Installing the Transmitters 14
- Installing a Keyswitch 14
- 4204_conn-1-V0 15
- On-Board Triggers 16
- Long Range Radio Connections 17
- 4285/4286 18
- Programming Overview 19
- Pager Programming 20
- Function Keys 20
- Output Devices 20
- Zone Type Definitions 21
- Mechanics of Programming 23
- Table of Device Addresses 24
- Installation Instructions 24
- Data Field Programming 25
- Dialer Programming 27
- System Status Report Codes 28
- Miscellaneous System Fields 30
- Pager Programming Fields 32
- Zone Conditions Represented 34
- Keypad Programming Fields 35
- Menu Mode Programming 37
- 02 HARDWIRE TYPE 38
- ✱ TO SKIP 38
- TO CONFIRM? 39
- AXXX-XXX – 40
- These transmitters 41
- Zone List Overview (∗ 45
- ∗81 Menu Mode) 45
- Zone List Programming 45
- ∗57 Menu Mode) 46
- Programming Function Keys 46
- (For Adding Custom Words) 49
- HH MMAM 0010000 51
- 0=NO 1=YES X 51
- SECTION 6 53
- Report Code Formats 53
- Ademco Contact ID 55
- User Security Codes 56
- Setting the Real-Time Clock 56
- Keypad Functions 57
- Panic Keys 58
- Power Failure 58
- Testing the System 59
- Go/No Go Test Mode 60
- SECTION 8 61
- SECURITY CONTROL 61
- COMPATIBLE DEVICES 61
- Regulatory Agency Statements 65
- UL NOTICES 66
- Limitations and Warranty 67
- – INDEX – 69
- SUMMARY OF CONNECTIONS 71
- ÊK0735V3^Š 72
Related products and manuals for Security access control systems ADEMCO VISTA 10
(68 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals