ADEMCO VISTA 10 Setup Guide download pdf (Page 71)

VISTA-10P-SOC-V2

CLASS 2 PLUG-IN TRANSFORMER

16.5VAC, 25VA

(e.g. ADEMCO No. 1321).

(USE No. 1321CN IN CANADA)

TO 110VAC

UNSWITCHED

OUTLET (24HR)

THIS EQUIPMENT SHOULD BE INSTALLED

IN ACCORDANCE WITH THE NATIONAL

FIRE PROTECTION ASSOCIATION'S

STANDARD 72, CHAPTER 2 (NATIONAL

FIRE PROTECTION ASSOCIATION,

BATTERY-MARCH PARK, QUINCY,MA

02269).

PRINTED INFORMATION

DESCRIBING PROPER INSTALLATION,

OPERATION,TESTING, MAINTENANCE,

EVACUATION PLANNING AND REPAIR

SERVICE IS TO BE PROVIDED WITH THIS

EQUIPMENT.

24-HR BATTERY STANDBY REQUIRED FOR

FIRE INSTALLATIONS. USE 12V, 17.2AH

BATTERY FOR 600mA AUX POWER. SEE

INSTRUCTIONS.

BATTERY CAPACITY FOR EMERGENCY

BURGLARY STANDBY USE AT LEAST 4 HRS

USE UL LISTED LIMITED ENERGY

CABLE FOR ALL CONNECTIONS

FOR COMPLETE

INFORMATION, SEE

INSTRUCTIONS K0735

ALARM OUTPUT

10.5–13.8VDC, 2A MAX.

(600mA MAX. FOR UL

USAGE, INCLUDING

AUX POWER) STEADY

FOR BURGLARY/PANIC,

TEMPORAL PULSE

SOUNDING FOR FIRE.

CAN USE ADEMCO No. 702

SIREN, OR 12V BELL).

SEE INSTRUCTIONS.

CHARGING VOLTAGE

13.8VDC. MAXIMUM

CHARGING CURRENT

650mA.

BATTERY

12V, 4AH

BLACK

RED

SEALED LEAD-ACID TYPE.

BATTERY NORMALLY NEED NOT BE

REPLACED FOR AT LEAST 3 YRS.

TO DETERMINE TOTAL STANDBY LOAD

ON BATTERY, ADD 100mA TO TOTAL OF

AUX. POWER OUTPUT AND REMOTE

KEYPAD CURRENTS.

FLYING LEADS

FOR BATTERY

CONNECTION

CONNECTION OF THE FIRE ALARM

SIGNAL TO A FIRE ALARM

HEADQUARTERS OR A CENTRAL STATION

SHALL BE PERMITTED ONLY WITH THE

PERMISSION OF THE LOCAL AUTHORITY

HAVING JURISDICTION. THE BURGLAR

ALARM SIGNAL SHALL NOT BE

CONNECTED TO A POLICE EMERGENCY

NUMBER.

OPTIONAL

FOR UP TO 16 ADDITIONAL RF ZONES

( AND/OR UP TO 4 RELAYS)

ADEMCO 5881* Type

RF RECEIVER

WIRELESS ZONES

ADEMCO No. 4204 RELAY MODULE

(4 OUTPUT RELAYS)

SET UNIT’S DIP SWITCH FOR DEVICE

ADDRESS 12

SEE INSTRUCTIONS.

BLK

RED

GRN

YEL

21 22

EARTH

GROUND

SEE

INSTRUCTIONS

FOR PROPER

GROUNDING

(VIA RJ31X* JACK AND DIRECT

CONNECT CORD)

*CA38A IN CANADA

DOC LOAD NO.: 3

RED: KEYPAD PWR (

)

GREEN: DATA IN FROM KEYPAD

YELLOW: KEYPAD DATA OUT

▲

REMOTE

KEYPADS

AND OTHER

ADDRESSABLE

DEVICES

(e.g. 5800TM,

4285/4286, LRR,

4204, 5881)

WARNING:

TO PREVENT RISK OF SHOCK,

DISCONNECT TELEPHONE LINE AT TELCO

JACK BEFORE SERVICING THIS UNIT.

BLK

RED

GRN

YEL

TO TERM 4

TO TERM 5

TO TERM 6

TO TERM 7

BLK

RED

GRN

YEL

AND/OR

RING

(GRAY)

TIP

(GREEN)

RING

(RED)

INCOMING

PHONE LINE

HANDSET

TELEPHONE WIRING

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE 6

MAXIMUM LOOP RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR)

•

RESPONSE, ZONES 1-6: 10, 350, OR 700 MSEC (PROGRAMMABLE)

5-PIN CONNECTOR

FOR ON-BOARD TRIGGERS

SEE INSTRUCTIONS.

(USE KEYPAD CABLE)

TIP

(BROWN)

}

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

COMPLIES WITH FCC RULES, PART 68.

FCC REGISTRATION NO. 5GBUSA-44003-AL-E

RINGER EQUIVALENCE: 0.1B.

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS

SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED

TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.

RED JUMPER

CUT FOR BELL SUPERVISION.

ALSO, CONNECT 2000 OHM

RESISTOR DIRECTLY ACROSS

SOUNDER.

FOR CONNECTION OF OPTIONAL 4285 OR 4286 VIP

MODULES TO PHONE TERMINALS, SEE INSTRUCTIONS.

5881L: UP TO 8

5881M: UP TO 16

NOTE:

KEYPAD (S)

CURRENT AND

ALL OTHER

DEVICES

DRAWING

POWER FROM

TERMS 4 & 5

MUST BE

INCLUDED IN

AUX CURRENT

DRAIN

CALCULATIONS.

2000

OHMS

EOLR

2000

OHMS

EOLR

2000

OHMS

EOLR

2000

OHMS

EOLR

2000

OHMS

EOLR

2000

OHMS

EOLR

GND

+12 AUX

1234 5

OUTPUT 18

(TRIG. 2)

OUTPUT 17

(TRIG. 1)

ALL DEVICES AND ACCESSORIES

USED IN A CANADIAN INSTALLATION

MUST BE LISTED FOR USE IN CANADA

BATTERY FUSE

FOR REPLACEMENT,

USE SAME VALUE

(e.g. ADEMCO No. 90-12)

SET

RECEIVER’S

DIP SWITCH

FOR DEVICE

ADDRESS

OF “0”.

SEE

INSTRUCTIONS.

REMOTE KEYPADS

CAN USE 6150 OR 6160

KEYPADS. LOCAL

PROGRAMMING

MUST BE DONE WITH A

6160, BUT NEED NOT

REMAIN IN THE SYSTEM

(SET TO ADDRESS 16).

POWER SHUTDOWN NOTE:

SYSTEM SHUTS DOWN SENSOR

DETECTION PROCESSING IF

CONTROL'S VOLTAGE DROPS

BELOW 9.6V.

ADEMCO VISTA-10P / VISTA-10PSIA

SUMMARY OF CONNECTIONS

*5882 IN CANADA

NOT USED

BLACK: KEYPAD GROUND (- ) RETURN

AUX. POWER

OUTPUT

10.5-13.8VDC

600mA MAX.

(500mA MAX.

FOR UL

INSTALLATIONS)

ALL OUTPUTS

ARE POWER

LIMITED.

}

BLK

4-WIRE SMOKE DETECTOR CONNECTIONS

2000

OHMS

EOLR

HEAT

DETECTOR

RED

EOL

POWER

SUPERVISION

RELAY MODULE

A77-716B.

USE N.O.

CONTACT,

WHICH CLOSES

WHEN POWER

IS APPLIED.

VIOLET

AUX PWR

OUTPUT

TERMINALS

BLK

TO ZONE TERM. ( )

RELAY

CONTACT OPENS MOMENTARILY

UPON FIRE ALARM RESET

PROGRAM RELAY

AS ZONE TYPE 54

(FIRE ZONE RESET)

4-WIRE SMOKE

OR COMBUSTION

DETECTOR

N.C.

N.O.

TO OUTPUT 17

PROGRAM OUTPUT 17 FOR

"OUT NORM LOW" = YES IN

79 MENU MODE AND AS ZONE

TYPE 54 IN 80 MENU MODE

MAX. CURRENT = 100 mA

(UP TO 16 DETECTORS

PLUS EOL MODULE)

Figure 17. Summary of Connections

1 2 ... 66 67 68 69 70 71 72

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 71

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10