ADEMCO VISTA 10 Setup Guide download pdf (Page 40)

Zn ZT RC IN: L

10 00 10 RF 1

A summary screen with the selected zone’s current programming appears.

Begin programming zone information as follows:

Enter Zone Type (ZT; see Zone Types listed in *56 Menu Mode “Zone Type” prompt), Report

Code (RC), and Input Device Type (IN)* sequentially (Loop Number (L) is entered at the next

prompt).

• Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the

screen.

• Use the [C] key to copy the previous zone’s attributes.

* If HW (hardwired) or AW (Auxiliary) is entered for Input Device Type, the display will be

similar to the prompt shown, except that HW or AW will be under “IN”.

Press [∗] to save the programming and continue. If needed, press the [#] key to back up

without saving.

For wireless devices (input types RF, UR, BR), continue to the serial number/loop number

prompt.

For wired devices, return to the initial summary screen prompt to begin programming the

next zone.

10 INPUT S/N: L

AXXX-XXX –

Zn ZT P RC In L

10 03 1 10 RF: 1s

Manually enter the serial number (found on the transmitter label), by typing digits in the

“X” locations, using the [A] (advance) or [B] (back) keys as required.

Transmit two open/close sequences. If using a button-type transmitter, press and release the

button twice, but wait about 4 seconds before pressing the button the second time.

If you want to copy the previous zone’s serial number, press the [C] key.

Press [∗] to advance to the loop number, then enter loop number.

Press [∗] to accept the existing serial and loop number and continue to the “Confirm” prompt

described in *56 Menu mode above.

If necessary, press [#] to back up and re-enter or edit the serial number.

If the serial number transmitted matches the serial number entered, the keypad will beep 3

times and a summary display will appear, showing the programmed information for that

zone.

Press [∗] to begin programming the next zone. See first “Summary Screen” prompt

paragraph.

Wireless Key Programming Templates

This procedure programs the wireless keys, but a key is not active for arming/disarming until

it is assigned to a user number (see System Operation section, assigning attributes command).

Enter this mode by pressing the D key while at the *58 Menu mode Summary Screen. The following

prompts appear.

TEMPLATE ?

1–6 1

Enter desired template number 1–6 (see chart).

Press [#] if you want to return to *58 Menu mode Summary Screen.

If necessary, press [#] to back up and re-enter template number.

Press [∗] to continue to template display.

L 01 02 03 04

T 23 22 21 23

The selected template is displayed.

Top line of display represents loop numbers, bottom line represents zone type assigned for

each loop.

Press [∗] to accept template and continue.

ENTER START ZONE

00 = QUIT 36

The system will search for the highest available consecutive 4-zone group (the four zones in

the case of the 5804 and 5804BD), and display the lowest zone number of the group.

If you want to start at a different zone, enter the zone desired, and press [∗]. If that zone

number is displayed, the system has the required number of consecutive zones available,

beginning with the zone you entered. If not, the system will again display a suggested zone

that can be used.

If the required number of consecutive zones is not available at all, the system will display

“00”.

To quit this mode and return to *58 Menu mode, enter 00 at this prompt.

Press [∗] to accept and continue.

Installation Instructions

5-4

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 40

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10