ADEMCO VISTA 10 Setup Guide download pdf (Page 38)

10 Report Code

1st 01 2nd 00 10

Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn

consisting of 2 numerical digits. For example, for a report code of “10,” enter 01 and 00.

For Contact ID

, entering any non-zero entry as the first digit enables the report code for

this zone. Refer to the System Communication section for information about report codes

and formats.

Report code digits: 1-9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F

00 to disable; [∗] to continue

02 HARDWIRE TYPE

EOL 0

This prompt appears only for zone numbers 01-06.

Enter the desired hardwire type:

0 = EOL; 1 = NC; 2 = NO

[∗] to continue

02 Response Time

This prompt appears only for hard-wired zones 01-06 (zone 02 is used as an example in

display).

Enter the desired response time for this zone:

0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 seconds

[∗] to continue

10 INPUT TYPE

RF TRANS 3

For wired zones 1-6, the Input Type automatically displays as HW and cannot be edited.

All of the RF transmitters have one or more unique factory-assigned input loops (ID codes).

Each of the input loops requires its own programming zone (e.g., a 5804's four button inputs

require four programming zones). Select the desired input type for the transmitter zone

being programmed.

3 = RF (supervised RF transmitter; sends fault, restore, and low-battery signals, and sends

periodic check-in signals; transmitter must stay within receiver's range)

4 = UR (unsupervised RF transmitter; sends fault, restore, and low-battery signals, but

does not send periodic check-in signals; transmitter may be carried off-premises)

5 = BR (unsupervised button type RF transmitter; sends fault and low battery signals when

activated, does not send restore or check-in signals; transmitter may be carried off-

premises)

[∗] to continue

10 INPUT S/N: L

A022-4064 1

For wireless transmitters, enroll the serial number and loop number.

1. a. Transmit two open/close sequences. If using a button-type transmitter, press and

release the button twice, but wait about 4 seconds before pressing the button the

second time.

b. Manually enter the 7-digit serial number printed on the label of the transmitter.

Press the [∗] key to move to the “L” position, then enter the loop number (see Loop

Identification chart on back cover).

If desired, you can press the [C] key to copy the previously enrolled serial number

(used when programming a transmitter with several input loops). The cursor moves to

the loop number position.

c. To delete an existing serial number, enter 0 in the loop number field. The serial

number will change to 0's. If 0 was entered in error, simply re-enter the loop number or

press [#], and the serial number will return to the display.

2. Press [∗] to continue. The system now checks for a duplicate serial/loop number

combination.

10 INPUT S/N L

A022-4064 1

If the serial/loop number combination is not a duplicate in the system, a display showing the

serial number and loop number entry appears.

[∗] to continue

XMIT TO CONFIRM

PRESS ✱ TO SKIP

This prompt will only appear if you answered “Yes” at the “SET TO CONFIRM” prompt.

The system now enters a confirmation mode so that the operation of the actual programmed

input can be confirmed.

Activate the loop input or button that corresponds to this zone.

[∗] to continue

Installation Instructions

5-2

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 38

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10