ADEMCO VISTA 10 Setup Guide download pdf (Page 32)

FIELD

TITLE and EXPLANATION

*96

Command to Initialize CSID and Subscriber Account Number

This is a command function, not a data field. Use this command, if necessary, to reset all subscriber account

numbers and the internal CSID to the factory default values.

*97

Command to Reset System to Factory Default Values

This is a command function, not a data field.

Pressing ∗97 resets all data fields to the factory default values

(shown on the Program Form).

IMPORTANT: Do not press ∗97 to load defaults if any programming has been done previously—data

already programmed into the system will be changed!

*98

Command to Exit Program Mode (with installer code lockout)

Exits Programming Mode and prevents re-entry by:

Installer Code + [8] + [0] + [0]. To enter the programming mode if

∗

98 was used to exit, you must first

power the system down. Then power up again, and press [∗] and [#] at the same time, within 50 seconds

of powering up.

See field *88 for other Program mode lockout options.

*99

Command to Exit Program Mode

Exits Programming Mode and allows re-entry by:

Installer Code + [ 8] + [0] + [0] or by: Pressing [∗] and [#] at the same time, within 50 seconds of power-up

Pager Programming Fields

FIELD

TITLE and EXPLANATION

*160

Pager 1 Phone No.

Enter the pager phone number. If you enter fewer than 20 digits, exit by pressing [∗] and next field

number. To clear entries from this field, press ∗160∗.

*161

Pager 1 Characters

Enter up to 16 optional characters, which may be sent as a prefix to the 7-digit system status code sent

to Pager 1 (if used). Phone number in field *160 must be entered. If fewer than 16 characters, exit by

pressing [∗] and next field number. To clear entries from this field, press ∗161∗.

For example, these optional 16 characters may be composed of the following:

• paging company PIN number, subscriber account number, ∗ (enter # + 11 to send ∗), # (enter # + 12

to send #), pause (enter # + 13 to allow a 2-second pause; some paging systems require pause)

• Any special character(s) the end user may decide to transmit

The format for the 7-digit system status code is defined as follows:

Pager Format: XXX-YYYY where:

XXX = 3-digit event code: 911 = Alarm 101 = Opening (disarm)

811 = Trouble 102 = Closing (arm AWAY)

YYYY = 4-digit user or zone number (depending on type of event).

The first digit is “1,” followed by the 3-digit user or zone number, or “0,” followed by a 3-digit

device address number.

Example 1. Pager displays: 911– 1004: an alarm (911) caused by a fault in zone 4 (1004).

Example 2. Pager displays: 102– 1005: a closing–system arming (102) by User 5 (1005).

*162

Pager 1 Report Options

Enter the types of reports to be sent to the pager.

Open/close reports go to pager only when arming (close)/disarming (open) from a keypad using a

security code; auto-arming/disarming, arming with assigned button, and keyswitch arming do not send

pager messages.

Miscellaneous System Fields

*172

Pager Delay Option for Alarms

Enter the desired pager delay (none, 1, 2, or 3 minutes) for alarms. This delay applies to all pagers in

the system.

*177

Device Duration 1, 2

Enter the desired duration for output action options 5 (duration 1) and 6 (duration 2) programmed in

∗80 Output Function Programming.

*181

50/60 Hz AC Operation

Select the type of AC power applied to the control (option is used for Real-Time Clock synchronization).

Installation Instructions

4-8

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 32

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10