ADEMCO VISTA 10 Setup Guide download pdf (Page 44)

“A”

01 Zn List

If zone list was selected, this screen appears. Otherwise skip to the next prompt.

Enter the desired zone list number associated with this output number:

01-08 = zone list (Do not use pager zone list 09 in output definitions)

Enter the zone list event that will activate this output:

Enter Event 0 = restore; 1 = alarm;

Alarm 1 2 = fault; 3= trouble

NOTE: For alarm, fault, and trouble, an event on ANY zone in the list activates the output,

but ALL zones in the list must be restored before the output is restored.

Press [∗] to continue and skip to the “Output Action” prompt.

“B”

01 Enter Zn type

Perimeter 03

If zone type was selected, this screen appears. Otherwise skip to the next prompt.

Enter the desired zone type for this output number.

CHOICES FOR ZONE TYPES:

00 = Not Used 05 = Trouble Day/Alarm Night 12 = Monitor Zone

01 = Ent/Exit #1 06 = 24 Hr Silent 14 = Carbon Monoxide

02 = Ent/Exit #2 07 = 24 Hr Audible 16 = Fire w/verification

03 = Perimeter 08 = 24 Hr Aux 23 = No Alarm Response

04 = Interior Follower 09 = Fire 24 = Silent Burglary

10 = Interior w/Delay 77 = Keyswitch Zone

81 = AAV Monitor Zone

90 = Configurable

CHOICES FOR SYSTEM OPERATION:

20 = Arming–Stay 36 = At Bell Timeout*** 52 = Kissoff

21 = Arming–Away 38 = Chime 54 = Fire Zone Reset

22 = Disarming 39 = Any Fire Alarm 58 = Duress

31 = End of Exit Time 40 = Bypassing 60 = AAV

32 = Start of Entry Time 41 = AC Power Failure 66 = Function Key†

33 = Any Burglary Alarm 42 = System Battery Low 67 = Bell Fail

43 = Comm. Failure 68 = Telco line cut

78 = Keyswitch Red LED

79 = Keyswitch Green LED

*** Or at Disarming, whichever occurs earlier.

†

Use *57 Menu Mode to assign the function key (function “07”).

Note: In normal operation mode:

Code + # + 7 + NN Key Entry starts Device NN.

Code + # + 8 + NN Key Entry stops Device NN.

Press [∗] to continue and skip to the “Output Action” prompt.

“C”

01 Enter Zn No.

If zone number was selected, this screen appears.

Enter the desired zone number associated with this output number.

Press [∗] to continue.

Enter the zone event that will activate this output.

01 Enter Event

0 = restore; 1 = alarm/fault/trouble

Restore 0

Press [∗] to continue to the “Output Action” prompt

01 Output Action

Close for 2 sec 1

Enter the desired device action as listed below.

0 = off 4 = Change Device State

1 = Close for 2 seconds 5 = Duration 1 (see data field *177)

2 = Stay Closed 6 = Duration 2 (see data field *177)

3 = Pulse 1 sec ON, 1 sec OFF

Press [∗] to continue.

Enter Output No.

R02 02

Enter the device output number (programmed in *79 Menu Mode) you want associated with

this output.

01-04 = output no.

17-18 = on-board triggers

Press [∗] to continue.

02 A E P TRIG

R02 1 1 3 ZL=00

A summary screen appears showing the programmed settings.

Press [∗] to return to output function number prompt.

Installation Instructions

5-8

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 71 72

Comments to this Manuals

No comments

ADEMCO VISTA 10 Setup Guide Page 44

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO VISTA 10