ADEMCO Vista-20HW Troubleshooting Guide Page 20
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3. If the number of digits that you need to enter in a data field is less than
the maximum digits available (for example, the phone number field), enter
the desired data, then press * and the next data field number to be
programmed.
4. If you try to enter a non-existent field, the keypad will display EE or Q
Entry Error. Simply re-enter [*] plus a valid field number.
Reviewing a Data Field/Erasing an Entry in a Data Field
Press[#] plus Field No. Data will be displayed for that field number. No
changes will be accepted in this mode.
To delete an entry in a field, press [*] plus Field No. + [*I. (Applies only to
fields *40–*46, and *94).
Interactive Mode Programming
(*56, *SO, *S1, and *82)
Typicalpromptdisplayed
Press [*] plus interactive mode No. (for example, *56). The Alpha keypad
during interactivemode
will display the first of a series of prompts requesting entries.
programming
A detailed procedure (with displays of prompts) is provided in those sections
Enter Zn Num.
1
where programming in the interactive mode is to be performed.
(00 = Quit)
01
1
Interactive Mode
Used To Program
Zone Number~
*56 Zone Programming Zone characteristics, report codes, alpha
descriptors and serial numbers
*8O Relay Programming
4229 or 4204 Relay modules, or Powerline
Carrier devices
*81 Zone List Programming
Zone Lists for relaylpowerline carrier activation
*82 Alpha Programming Zone alpha descriptors
Loading Factory Defaults
To load the factory defaults, enter the programming mode, press *97, then
exit the programming mode.
*96 resets the Subscriber Account number and CSID in preparation for an
initial download.
PrOgramnu
‘ng System Setup ~~elds
The following program fields must be programmed before doing any zone
programming.
*2S -D ZONE EXPANSION
u
Use this field to select the type of expansion unit being used, as follows:
O= none; 1 = 4219; 2 = 4229; 3 = 4204. Default is O.
*3o KEYSWITCH ENABLE
u
This field must be enabled (enter 1) if using a keyswitch. The keyswitch
must be connected to zone 7, which can then not be used for any other
purpose.
Default is O (no keyswitch).
Note: If keyswitch is enabled, in menu mode *56 the Zone Type (ZT) for
zone 7 will show “77”, and will not be accessible for programming.
Exiting the Programming
g Mode
*99 allowsre-entry~to the progr~ mode using
Installer Code + 8 0 0.
W8 mbits re-entryintothe programming mode using the Installer code.
-20-
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.259 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals