ADEMCO Vista-20HW Troubleshooting Guide Page 85
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
General Information Notethat if you enabled QUICK ARM for the partition (field *21), the [#] key
can be pressed instead of entering the partition’s security code, for any of the
arming procedures (Away, Stay, Instant, Maximum, etc.). The security code is
always required, however, when disarming the system.
The keypad allows the user to arm and disarm the system, and perform other
system functions, such as bypassing zones, and display zone descriptors. Zone
and system conditions (alarm, trouble, bypass) are displayed in the Display
Window.
When an alarm occurs, keypad sounding and external sounding will occur,
and the zone(s) in alarm will be displayed on the keypad. Pressing any key
will silence the keypad sounder for 10 seconds. Disarming the system will
silence both keypad and external sounders. When the system is disarmed,
any zones that were in an alarm condition during the armed period will be
displayed (memory of alarm). To clear this display, simply repeat the disarm
sequence (enter the security code snd press the OFF key) again.
The keypads also feature chime annunciation, and 3 panic key pairs, or
individualpanickeys(dependingonkeypadtype – seePanic Keys), forsilent,
audible,fireorpersonalemergencyalarms. Thesekeyscannoti~ the central
stationofan alarmcondition,if that serviceis comected.
Arming Functions The followingis a brief list of system commands. For detailedinformation
concerningsystemiimctions,referto the User’s Manual.
Disarmed, Not Ready .....Before arming, the system must be in the
READY condition(all zonesmust be intact).If
the “NOT READY’ message appears, pressthe
READY [*] keyto displayfaultedzones.
Arming Away ...................... Entercode+ AWAY [2].
Arming Stay ........................ Entercode + STAY [3].
Arming Instant ..................Enter code + INSTANT [7].
Arming Maximum ............. Enter code + MAXIMUM [4].
Disarming ........................... Enter code + OFF [1].
Bypassing Zones ................Enter code + BYPASS [6]+ zone number(s).
Forced (Quick) Bypass .....
(If enabled) To automatically bypass all faulted
zones,
use the “Quick Bypass” method:
Enter code + BYPASS, then wait for all open
zones to be displayed. Arm when display
indicates “bypass” and “ready to arm”.
Chime Mode ........................ Entercode+ CHIME [9].
Toturnchimeoff,entercode+ CHIME again.
SUMMARY OF ARMING MODES
Features for Each Arming Mode
Arming
Exit
Entry
Perimeter Interior
Mode
Delay
Delay Armed
Armed
AWAY
Yes
Yes
Yes
Yes
STAY
Yes Yes
Yes
No
I INSTANT I
Yes
I
No I Yes I
No
I
[-MAXIMUM i
Yes I No
I Yes I
Yes I
-65-
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.269 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals