ADEMCO Vista-20HW Troubleshooting Guide download pdf (Page 59)

100

4. For selection of the next word (e.g., DOOR), repeat step 3, as follows. .

Press key [3] until the first letter of the next word appears (e.g., “D”).

Then press [6] to display the first available word beginning with that

letter (e.g. DAUGHTERS). Press [3] repeatedly until the desired word

(e.g.,DOOR) appears. To accept the word, press [61,which toggles back to

the alphabet list.

5. When all desired words have been entered, press [8] to store the

description in memory.

6. Enter *NN, where NN is the next zone that you want to review or for

which you want to program a descriptor. To modi~ the descriptor, enter

*NN again. To exit this mode, press “*00”.

Adding Custom Words (will not be annunciated by the 42S5 Module)

You can add up to five installer-defined words can be added to the built-in vo-

cabulary. Each of the five “words” can actually consist of a “word string” of

one or more words, but no more than ten characters can be used for each

word or word string.

[3]

[11

[6]

[4]

[7]

[81

Advances through the

alphabet in ascending

order.

Moves through the

alphabetin descending

order.

Selects desired letter;

movescursorone space

to right.

Movescursorone space

to left.

Inserts a space at the

cursorlocation,erasing

any character located

there.

Savesthe new word in

thesystem’smemory.

Perform steps 1, 2, and 3 of Programming the Descriptors on a

previous page.

Select CUSTOM WORD mode (enter “1”) when the prompt CUSTOM

WORD ? is displayed.

Enter the number ([1]-[5]) of the custom word or word string to be

created (for example, if you are creating the first custom word or word-

string, enter [1], for the second, enter [2], etc.). A cursor will now appear

at the beginning of the second line.

One of two methods of entering the custom word’s characters can

now be used (refer to the CHAR4CTER LIST of letters, numbers, and

symbols on a following page):

Method 1:

Press the [#] key, followed by the two-digit entry for the first letter you

would like to display (e.g., [6][5] for “A”), or...

Method 2:

Use the [31key to advance through the list of symbols, numbers, and

letters. Use the [1] key to move back through the list.

When you have reached the desired character, press [6] to select it. The

cursor will then move to the right, in position for the next character.

Repeat steps 3 and 4 to create the desired word(s). Note that the [41key

can be used to move the cursor to the left, if necessary, and that key [71

can be used to enter a blank (or erase an efisting character). Remember,

no word or word-string can exceed 10 characters.

Press the [8] key to save the custom word(s) and return to the “CUSTOM

WORD ? display.

Repeat steps 2-5 for other custom words to be entered. To change a

custom word, just overwrite it. If no more are to be entered now, press [01

to return to the Descriptor entry. The custom word(s) will be

automatically added to the built-in vocabulary.

When zone descriptors are being entered as described in step 6 of

Programming the Descriptors, the custom word numbers are 250 to 254

for words 1 to 5 respectively.

When being entered as described in step 3 in Alternate Method For

Programming Zone Descriptors, each word will be found at the end of the ,

group of words that begin with the same letter as it does.

-59-

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 99 100

Comments to this Manuals

No comments

ADEMCO Vista-20HW Troubleshooting Guide Page 59

Comments to this Manuals

Related products and manuals for Security access control systems ADEMCO Vista-20HW