ADEMCO VISTA 10 Setup Guide Page 29
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
FIELD
TITLE and EXPLANATION
*62
AC Loss Report Code
Enter the appropriate report code. Timing of this report is random with up to a 4-hour delay. If AC
restores before the report goes out, there is no “AC RESTORE” report.
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations.
*63
Low Bat Report Code
Enter the appropriate report code; sent when a low-battery condition exists in the system’s battery.
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations.
*64
Test Report Code
Enter the appropriate report code, which is sent periodically to test that the communicator and phone
lines are operational. Frequency of report is set in Scheduling mode (event 11) or by the following key
commands:
installer code + [#] + 0 + 0 = test report sent every 24 hours
installer code + [#] + 0 + 1 = test report sent once per week
installer code + [#] + 0 + 2 = test report sent every 28 days
Each mode sets schedule 2 to the selected repeat option; first test report sent 12 hours after command.
NOTE: Make sure the Real-Time Clock is set to the proper time before entering the test report schedule
command to ensure that test reports are sent when expected. (see Setting the Real-Time Clock section).
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations.
*65
Open Report Code
Enter the appropriate report code, which is sent upon disarming of the system.
UL: Required for UL commercial burglar alarm installations.
*66
Arm Away/Stay Report Code
Enter appropriate report code. NOTE: “OPEN” reports not sent if associated closing report is not enabled.
*67
RF Trans. Low Batt. Report Code
Enter the appropriate report code; sent when a wireless transmitter low-battery condition exists.
UL installations: must be enabled if wireless devices are used.
*68
Cancel Report Code
Enter the appropriate report code; sent upon disarming of the system after an alarm was reported.
VISTA-10PSIA: Default = code enabled
*69
Recent Closing Report VISTA-10PSIA only
Always enabled. Field does not apply to other controls.
Similar to the Exit Error condition described in field *59, but occurs if any burglary zone is faulted within two
minutes after the initial exit delay expires. Disarming the system within the two minutes stops the alarm
sound and displays " ALARM CANCELED " or "CA" and the faulted zone number. No message is sent to the
Central Monitoring Station.
If the system is not disarmed within two minutes, the alarm sound continues and a “recent closing” and a “zone
alarm” message are sent to the Central Monitoring Station (after dial delay expires).
*70
Alarm Restore Report Code
Enter the appropriate report code; sent when an alarm zone is restored to its non-faulted condition.
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations.
*71
Trouble Restore Report Code
Enter the appropriate report code, which is sent when a trouble in a zone is restored
UL: Required for UL commercial burglar alarm installations.
*72
Bypass Restore Report Code
Enter the appropriate report code, which is sent when a zone that has been bypassed is unbypassed.
UL: Required for UL commercial burglar alarm installations.
*73
AC Restore Report Code
Enter the appropriate report code; sent when AC power has been restored after an AC power outage.
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations
.
*74
Low Bat Restore Report Code
Enter the appropriate report code; sent when a system low-battery condition is restored to normal.
UL: Required for UL commercial burglar alarm installations and for residential fire alarm installations.
*75
RF Xmtr Low Batt. Restore Code
Enter the appropriate report code; sent when a trans. low battery is restored (new battery installed).
UL installations: must be enabled if wireless devices are used. Required for UL commercial burglar
alarm installations and required for residential fire alarm installations.
4-5
- ADEMCO VISTA-10P 1
- ADEMCO VISTA-10PSIA 1
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 5
- SECTION 2 7
- Cabinet and Lock 7
- DETAIL A 8
- DETAIL B 8
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Wiring the AC Transformer 10
- Backup Battery 10
- Earth Ground 11
- Hardwire Zones 12
- Smoke Detectors 12
- Installing a 5800TM Module 13
- Installing the RF Receiver 13
- Installing the Transmitters 14
- Installing a Keyswitch 14
- 4204_conn-1-V0 15
- On-Board Triggers 16
- Long Range Radio Connections 17
- 4285/4286 18
- Programming Overview 19
- Pager Programming 20
- Function Keys 20
- Output Devices 20
- Zone Type Definitions 21
- Mechanics of Programming 23
- Table of Device Addresses 24
- Installation Instructions 24
- Data Field Programming 25
- Dialer Programming 27
- System Status Report Codes 28
- Miscellaneous System Fields 30
- Pager Programming Fields 32
- Zone Conditions Represented 34
- Keypad Programming Fields 35
- Menu Mode Programming 37
- 02 HARDWIRE TYPE 38
- ✱ TO SKIP 38
- TO CONFIRM? 39
- AXXX-XXX – 40
- These transmitters 41
- Zone List Overview (∗ 45
- ∗81 Menu Mode) 45
- Zone List Programming 45
- ∗57 Menu Mode) 46
- Programming Function Keys 46
- (For Adding Custom Words) 49
- HH MMAM 0010000 51
- 0=NO 1=YES X 51
- SECTION 6 53
- Report Code Formats 53
- Ademco Contact ID 55
- User Security Codes 56
- Setting the Real-Time Clock 56
- Keypad Functions 57
- Panic Keys 58
- Power Failure 58
- Testing the System 59
- Go/No Go Test Mode 60
- SECTION 8 61
- SECURITY CONTROL 61
- COMPATIBLE DEVICES 61
- Regulatory Agency Statements 65
- UL NOTICES 66
- Limitations and Warranty 67
- – INDEX – 69
- SUMMARY OF CONNECTIONS 71
- ÊK0735V3^Š 72
Related products and manuals for Security access control systems ADEMCO VISTA 10
(68 pages)
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.639 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals