ADEMCO Vista-20HW Troubleshooting Guide Page 24
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Progr
amming Hard-Wwed Zones
1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the
Partition 1 keypad terminals on the control, power up the system
temporarily. If you had previously connected the AC transformer to the
control panel, you need only plug in the transformer (to 120VAC outlet) to
power up the system.
2. Enter the programming mode by keying the following on the Alpha
keypad Installer code (41 12) + 8 + O+ O.
Note that it is not possible to enter the programming mode if Partition 2
is in an armed state.
3. Press *56. Note that this is an interactive programming mode. You will
use it to program zone numbers, zone types, partition numbers, alarm
report codes, and to program response times for hard-wired zones.
II
Enter Zn Num.
(00 = Quit)
01
II
‘Ilmicalsummarydimlay
J.Zone Number
II
02 Zone Type
Perimeter
03
II
ZoneType ~
Upon entering *56 mode, this prompt will be
displayed. Enter the first zone number that
you wish to program (or [0][0] to exit zone
programming). If you are starting with zone 2,
enter “02”. Press * to continue.
A summary display will appear, showing the
present status of that zone’s programming.
Zn = zone number;
ZT = zone type;
P = partition to which zone is assigned;
RC = report code for that zone;
In= input type of zone;
RT = response time for that zone.
Values displayed are currently programmed
values.
If it is programmed satisfactorily, press [#] to
back up one step and enter the next zone
number, if desired.
If you want to change a zone’s programming,
press [*]. A prompt for Zone Type will appear.
Each zone must be assigned a zone type, which
defines the way in which the system responds
to faults in that zone. A detailed explanation of
each zone type is provided in “Response Type
Definitions” in Section 16. ZONE RESPONSE
TYPE DEFINITIONS.
Enter the desired
below.
00. ZoneNot Used
01= Entry/Exit#1
02= Entry/Exit#2
03= Perimeter
04= InteriorFollower
zone type code, as listed
07= 24 Hr Audible
08.24 Hr Aux
09= Fire (W/verif.)*
10= Interiorw/Delay
23= No Alarm
05. TroubleDay/AlarmNight
Response
06= 24 HrSilent
24= SilentBurglary
* The verification” featureis only activewhen zone
type 09 is assignedto hard-wiredzone 1.
When the display shows the zone type you want,
Dress [*1 to continue.
-24-
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 2.487 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals