ADEMCO Vista-20HW Troubleshooting Guide Page 83
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Test Procedure
After installation is completed, each partition of the Security System should be
carefully tested, as follows.
1. With the System in the disarmed state, check that all zones are intact. If a
NOT READY message is displayed, press the [*I key to display the faulted
zone(s). Restore faulted zone(s) if necessary, so that READY message is
displayed. Fault and restore every sensor individually to assure that it is
being monitored by the system.
2. Enter the security code and press the TEST key. The outside sounder will
sound for 1 second. The keypad should sound 3 beeps each time a contact is
faulted. A test report should be sent (if programmed) to the Central Station
immediately. If the backup battery is discharged or missing, the sounder may
not turn on and a LOW BATTERY report will be transmitted with a TEST
report. The keypad will beep once per minute as a reminder that the system
is in the Test Mode. To turn off the test mode enter security code and press
the OFF key.
Alarm messages will be sent to the central station during the following
tests 3 and 4. Notify them
in advance that tests will be in progress.
3. Arm the systemandfault one or morezones.After 15 seconds(if optionaldi-
aler delay is selected),silence alarm sounder(s)by enteringthe code and
pressingOFF. CheckEntry/Exitdelayzones.
4. Check the keypad-initiatedalarms that are in the system by pressingthe
Panickey (keypairson somekeypads). If the systemhas been programmed
for audible emergency, the keypad will emit a steady alarm sound, and
ALARM and zone number willbe displayed.Silencethe alarmby entering
the security code and pressingOFF.
If the system has been programmedfor silent emergency,there will be no
audiblealarmsordisplays,but a reportwillbe sentto the centralstation.
5. If output Relay Units/PowerlineCarrierDevices have been installed, test
theirprogrammedaction.
6 Noti~ the centralstationwhen all tests are finished,and verifyresultswith
them.
NOTE:
THE TEST MODE WILL BE AUTOMATICALLY TERMINATED AFTER 4 HOURS
IF THE INSTALLER OR USER DOES NOT MANUALLY TERMINATE IT.
THIS INSURES THAT FIRE AND PANIC ZONES WILL NOT REMAIN
DISABLED.
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and
frequent testing by the user are vital to continuous satisfactory operation of any
alarm system.
The installer should assume the responsibility of developing and offering a regular
maintenance program to the user as well as acquainting the user with the proper
operation and limitations of the alarm system and its component parts.
Recommendations must be included for a specii% program of frequent testing (at
least weekly) to insure the system’s proper operation at all times.
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.931 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals