ADEMCO Vista-20HW Troubleshooting Guide Page 19
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
This section provides information on how programming is performed in this
system. It will enable you to understand how to enter and exit the
programming mode, and how to program the data fields and the user-friendly
interactive modes (*56, *80, *81, *82, *83). We therefore urge you to read
and understand the following before proceeding with the installation.
I
General Programming
Information
Characteristics for each installation are stored in non-removable, electrically
erasable, non-volatile EEROM memory. These must be programmed for the
particular installation to establish its specific alarm and reporting features.
It is possible to program the system at any time, even at the installer’s
premises prior to the actual installation. Simply apply power temporarily to
the control and then program the unit as desired.
Important Note: You cannot enter the programming mode unless
- partitions are disarmed.
There are two programming modes: data field programming and interactive
(menu) mode programming. Data field programming is used for setting
various system options and interactive programming is used for
programming zone information, programming relay outputs, and for learning
transmitter serial numbers.
.
::,:,
Programming can also be performed remotely from the installer’s officelhome,
using an IBM personal computer, a modem, and V-Link downloading
software. See the Section 18. REMOTE PROGRAMMING AND CONTROL
(DOWNLOADING).
Entering Program Mode
You may use one of the following methods:
a) Press both the [*I and [#] keys at the same time within 50 seconds
after power is applied to the Control, or
b) Mter power up, enter the Installer code (4 1 1 2)+8 O 0.
This method is disabled if you exit the program mode using *98 instead of
*99. See
“Exiting Program Mode” par~aph later in this section.
If a diHerent Installer code is subsequently programmed, use it instead of
4112 to gain access to the Programming
g mode.
Following entry into program mode, data field *2O will be displayed (this is
the first field in the system). The system will now accept entries for field =0.
1.
2.
Data F5ekl
Press[*I plus Field No. (for example, *21), then make the required entry.
When you have completely programmed a data field, the keypad will
“beep” three times and then automatically display the next data field in
sequence. Togo to a different field, press [*] plus the desired field No.
-19-
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 0.663 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals