ADEMCO Vista-20HW Troubleshooting Guide Page 58
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
t
Flashing Cursor if “6” is
pressed (system ready for
nextword).
SummaryDisday
II
+$
ZN 01 BACK
DOOR
I
I
Program Alpha ?
o =
No, 1 = Yes 00
I
I
Alpha Pgm -
82
II
9.
10.
11.
12.
13.
14.
Press “6” to accept the selected
word.
Note: If these are the only words you ~
are using for the descriptor, press “8”
instead of “6”
to save them in
memory.
The two words in our example have
now been entered. Note, however,
that up to three words may be
entered (provided the number of
characters will fit on the screen).
Press “8” to save all words in
memory.
The “A” with the flashing cursor over
it will disappear, indicating that the
word(s) are stored in memory for that
zone, as shown in the summary
display at the left.
To enter a descriptor for the next
zone, press * plus the desired zone
number (e.g.,
*02. The summary
display following step 4 previously
will appear. Now repeat steps 6
through 10 for the descriptor for the
next zone.
To exit the Alpha descriptor mode,
press
“*+O+(J”
at the summary
display.
This prompt will be displayed.
*
Press “O”. This will be displayed.
Press *99 to exit the programming
mode.
Alternate Method For Programmi
og Zone Descriptors
1. Performsteps1 through5 of previous method.
2. Note that the first letter of the alphabet appears after the zone number,
and that the zone number is automatically included with the description.
If there already is a description for the zone, the description will appear
(with no cursor, since this is a display mode). To enter or change a de-
scription, press
[*I+Zone Number again. A flashing cursor will now ap-
pear.
Assume, for example, that the desired description for zone 1 is BACK
DOOR.
3. Select the first letter of the desired description (note that “A’ is
already displayed).
Press key [3] repeatedly to advance through the alphabet (e.g., to “B”), or
key [1] to go backward. Then press [6] to display the first available “word
beginning with the desired letter (e.g., BABY).
Next, press [3] repeatedly to move forward, or [1] to move backward, until
the desired word is displayed (e.g., BACK). Then press [61 to accept the
word and toggle back to the alphabet list.
-58-
- VISTA”20HW 1
- LIST OF FIGURES 5
- HOW TO USE THIS MANUAL 6
- II double-hnebox 7
- Back-up Battery 11
- RErumn CLw 12
- CAmm Doon 90?70!4 12
- NOTEALLUNUSEDWIRESSHOULD 15
- READY (Fixed 18
- Zone Number~ 20
- ULINSTALLATIONS,ONLY ZONE 1 22
- 2-WIRE SMOKE UJ 22
- 2000 OHMS 23
- IJ%TCHINGTYPEGIASS 23
- BRE4KDEIECTOR 23
- Enter Zn Num 24
- (00 = Quit) 24
- Perimeter 24
- ‘1 ~~~~fRj~5e~on.10msec,u~ 25
- 6. Unplug the AC transformer 26
- (TERM S) 27
- (TERM 5) 27
- (TERM 7) 27
- Wined Expansion Zones 28
- 10 Report Code 29
- 1st 03 2nd 12 3C 29
- Check-Out Procedure 30
- For Wired Expansion Zones 30
- Relay/Powerline 31
- Carner Device Basics 31
- 4204 and 4229 Relay Modules 31
- Powerline Carrier 32
- ITO ‘IX-AL ON CONTROL 33
- Programming Options Defined 34
- 20= Arming+tay 37
- 31= EndofExitTime 37
- ~“ lfktSCreeIl 38
- Installing the 4285 Module 39
- 4285 Module WIMg 40
- 4285 WIRING TABLE 40
- 4285 WIRING NOTES 41
- Compatible 44
- Sounders 44
- Sounder Connections 45
- Programming 45
- Installing the Keyswitcb 48
- F4-----------a; 49
- For The Remote Keyswitch 50
- 07 Response Time 51
- Program Alpha? 51
- INCCMNQTELCO LINE 53
- Making the BatteryConnections 55
- Method 1: 59
- Method 2: 59
- ALPHA VOCABULARY LIST 60
- Report Code Formats 61
- I 110 I Fire Alarm 63
- Communication Programming 64
- ❑ Secondary ❑ 65
- Field %59 ent~ note: 66
- Press *65 OPEN REPORT CODE 67
- Press *68 67
- Press *9O EVENT LOGGING 68
- 11111111111 68
- ❑ Partition2 ❑ 71
- ❑ Part>n2 ❑ 73
- 2= All exceptOpen/Close,Test 74
- 4= All exceptOpen/Close,Test 74
- (NOT USED) 78
- Test Procedure 83
- Security Codes 84
- No I Yes I 85
- [A, or [11& [*I 86
- [B],m[*Ik [#l 86
- Trouble Conditions 87
- POSSIBLE CAUSE 88
- CONTACTING TECHNICAL SUPPORT 89
- REGULATORY AGENCY STATEMENTS 90
- LOOPS (A-H): 92
- Monitored Telephone Line 96
- THE LIMITATIONS OF THIS AUUtM 98
- OF PITTWAY CORPORATION 100
Related products and manuals for Security access control systems ADEMCO Vista-20HW
(12 pages)
(56 pages)© 2020, manymanuals.com. All rights reserved. | 2.291 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals